From: Nate Kleven (cciemail@intellinet.ws)
Date: Thu Apr 24 2003 - 03:41:24 GMT-3
I stand corrected! Thank you Dennis. In the DQoS class they recommend
that you use 12.2 software. Perhaps that is just a recommendation and
not written in stone.
Nate
-----Original Message-----
From: Brian Dennis [mailto:brian@labforge.com]
Sent: Wednesday, April 23, 2003 9:04 PM
To: 'Jason Cash'; ccielab@groupstudy.com
Subject: RE: Map-class frame XXX - when is service-policy output
available?
Check out IOS version 12.1T.
Rack6R2#sho ver | in (^IOS)|(bin)
IOS (tm) C2600 Software (C2600-JK2O3S-M), Version 12.1(5)T9, RELEASE
SOFTWARE (fc1) System image file is "flash:c2600-jk2o3s-mz.121-5.T9.bin"
Rack6R2#conf t
Rack6R2(config)#map-class frame-relay cisco Rack6R2(config-map-class)#?
Static maps class configuration commands:
default Set a command to its defaults
exit-class Exit from static map class configuration mode
frame-relay Configure Map parameters
help Description of the interactive help system
no Negate a command or set its defaults
service-policy class-based service policy
Rack6R2(config-map-class)#service-policy ?
input input policy
output output policy
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
Director of CCIE Training and Development - IPexpert, Inc.
Mailto: brian@ipexpert.net
Toll Free: 866.225.8064
Outside U.S. & Canada: 312.321.6924
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Jason Cash
Sent: Monday, April 21, 2003 2:13 PM
To: ccielab@groupstudy.com
Subject: Map-class frame XXX - when is service-policy output available?
I have been told in prior emails to apply a policy map to the 'map-class
frame-relay' portion of the config. However, I am unable to see this
option.
r4(config)#map-class frame-relay voice
r4(config-map-class)#?
Static maps class configuration commands:
default Set a command to its defaults
exit-class Exit from static map class configuration mode
frame-relay Configure Map parameters
help Description of the interactive help system
no Negate a command or set its defaults
At what point is this available as I swore I saw it once in the past?!
Also, what is the difference in configuring it this way:
class-map data
match access-group 106
class-map voice
match access-group 105
!
policy-map voice
class voice
priority 80
class data
priority 48
!
interface Serial0
ip address 150.50.100.5 255.255.255.224
encapsulation frame-relay
no ip mroute-cache
load-interval 30
service-policy output voice
frame-relay traffic-shaping
frame-relay class voice
frame-relay map ip 150.50.100.2 501 broadcast rtp header-compression
active connections 256 frame-relay map ip 150.50.100.5 501 frame-relay
map ip 150.50.100.6 501 broadcast no frame-relay inverse-arp !
map-class frame-relay SHAPE frame-relay cir 128000 frame-relay bc 1280
frame-relay be 0 no frame-relay adaptive-shaping
As opposed to configuring it like this (when it is available):
class-map data
match access-group 106
class-map voice
match access-group 105
!
policy-map voice
class voice
priority 80
class data
priority 48
!
interface Serial0
ip address 150.50.100.5 255.255.255.224
encapsulation frame-relay
no ip mroute-cache
load-interval 30
frame-relay traffic-shaping
frame-relay class voice
frame-relay map ip 150.50.100.2 501 broadcast rtp header-compression
active connections 256 frame-relay map ip 150.50.100.5 501 frame-relay
map ip 150.50.100.6 501 broadcast no frame-relay inverse-arp !
map-class frame-relay voice frame-relay cir 128000 frame-relay bc 1280
frame-relay be 0 service-policy output voice no frame-relay
adaptive-shaping
This archive was generated by hypermail 2.1.4 : Thu May 01 2003 - 13:36:04 GMT-3