From: Hung, Sing-Yu (Sing-Yu.Hung@pccw.com)
Date: Tue Apr 15 2003 - 01:18:45 GMT-3
Dear,
I haven't get your problem as below show.
r8#sho ver
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-JOS56I-L), Version 12.1(5)T14, RELEASE
SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 24-Dec-02 17:46 by ccai
Image text-base: 0x0307EEA8, data-base: 0x00001000
ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE
SOFTWARE (fc1)
r8 uptime is 2 hours, 52 minutes
System returned to ROM by reload
System image file is "flash:c2500-jos56i-l.121-5.T14.bin"
cisco 2500 (68030) processor (revision N) with 14336K/2048K bytes of memory.
Processor board ID 06177670, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)
Configuration register is 0x2102
r8#
r8#sho pol
Policy Map voip
Class voip
Weighted Fair Queueing
Bandwidth 128 (kbps) Max Threshold 64 (packets)
r8#sho clas
r8#sho class-map
Class Map match-all voip (id 2)
Match access-group 100
Class Map match-any class-default (id 0)
Match any
r8#sl 100
Extended IP access list 100
permit udp any any range 16384 32767
permit tcp any any eq 1720
r8#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r8(config)#int s1
r8(config-if)#no fai
r8(config-if)#no fair-queue
r8(config-if)#
r8#sho int s1
Serial1 is up, line protocol is up
Hardware is HD64570
Internet address is 140.4.68.8/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:09, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6598 packets input, 506741 bytes, 0 no buffer
Received 1189 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
6577 packets output, 458903 bytes, 0 underruns
0 output errors, 0 collisions, 10 interface resets
0 output buffer failures, 0 output buffers swapped out
7 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
r8#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r8(config)#int s1
r8(config-if)#serv o voip
r8(config-if)#
r8#sho int s1
Serial1 is up, line protocol is up
Hardware is HD64570
Internet address is 140.4.68.8/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:09, output 00:00:03, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 1/1 (allocated/max allocated)
Available Bandwidth 1030 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6602 packets input, 507011 bytes, 0 no buffer
Received 1190 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
6581 packets output, 459173 bytes, 0 underruns
0 output errors, 0 collisions, 11 interface resets
0 output buffer failures, 0 output buffers swapped out
7 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
r8#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r8(config)#int s1
r8(config-if)#ip rsvp ba
r8(config-if)#ip rsvp bandwidth ?
<1-10000000> Reservable Bandwidth(KBPS)
<cr>
r8(config-if)#ip rsvp bandwidth 128 20
r8(config-if)#
r8#
Bradford Hung
-----Original Message-----
From: bobby [mailto:bobby1@ctimail3.com]
Sent: Tuesday, April 15, 2003 10:45 AM
To: ccielab@groupstudy.com
Subject: Reg: RSVP & CBWFQ
Hi,
On router R1 I have configured CBWFQ and I am applying the same under
Interface Serial 1 on R1. I have also configured RSVP under the same
interface.
For RSVP I would like to enable WFQ on interface serial 1. But when ever I
give the "fair-queue" command under interface serial 1, I got an error
message that I have to remove CBWFQ first and only then I will be able to
apply the fair-queue command.
Now my question is how can I enable WFQ on interface Serial 1 for RSVP
without
removing CBWFQ from the same interface or is there is any other way of doing
it.
Tks.
This archive was generated by hypermail 2.1.4 : Thu May 01 2003 - 13:35:52 GMT-3