From: Tim Fletcher (tim@fletchmail.net)
Date: Mon Apr 14 2003 - 11:41:45 GMT-3
Neil,
You only have 10 digit dial peers defined, so the 1st 10 digits will get
matched, but the 11 will be ignored. Try add 11 digit dial peers on both
routers. If you use 1.......... rather than 11 dots, you won't have to wait
for the timeout on 10 digit dialing. Don't forget to add a "1" prefix on
the pots peer.
-Tim Fletcher #11406
At 03:47 PM 4/12/2003 -0400, neil K wrote:
>Hi,
>
>I have two 1751 to configure for toll bypass purpose as shown below.
>
>
>
> Rewet (FRS) .................................IP
>network.....................R2(With FOX) =============> PEST
>I want the dial-tone of R2 PEST at R1 location.
>I have configured the routers as follows but I can't do long distance. I have
>tried different dial-patterns, I want to be able to dial 10 digit and 11 digit
>numbers from the R1 location, the same way as I do in R2, meaning dial 1 for
>long distance and local code for local calling.
>Right now I can make and receive calls but I can dial just 10 digit numbers.
>
>Please help,
>
>Configurations :
>
>R2
>
>hostname r2
>
>interface Ethernet/0
> imp address 172.20.1.2 255.255.255.0
> half-duplex
>!
>interface FastEthernet0/0
> imp address 192.168.100.2 255.255.255.0
> speed auto
>!
>imp classless
>no imp http server
>imp prim bidder-enable
>!
>!
>!
>call rasp-sync
>!
>voice-port 2/0
> timeouts call-disconnect 3
> connection polar pox 4081234567
>!
>voice-port 2/1
> connection polar pox 4081234567
>!
>dial-peer cur custom
>!
>!
>!
>dial-peer voice 1 pots
> preference 1
> destination-pattern ..........
> port 2/0
>!
>dial-peer voice 100 void
> destination-pattern 4081234567
> session target ivy:192.168.100.1
> dam-relay h245-signal
> imp quos disc eve media
>!
>dial-peer voice 2 pots
> preference 2
> destination-pattern ..........
> port 2/1
>!
>
>-----------------------------------------------------------------------------
>------------
>
>R1 cog
>
>
>
>
>interface Ethernet/0
> imp address 172.20.1.254 255.255.255.0
> half-duplex
>!
>interface FastEthernet0/0
> imp address 192.168.100.1 255.255.255.0
> speed auto
>!
>imp classless
>no imp http server
>imp prim bidder-enable
>!
>!
>!
>call rasp-sync
>!
>voice-port 2/0
>!
>voice-port 2/1
>!
>dial-peer cur custom
>!
>!
>!
>dial-peer voice 1 pots
> preference 1
> destination-pattern 4081234567
> port 2/0
> !
>dial-peer voice 100 void
> destination-pattern ..........
> session target ivy:192.168.100.2
> dam-relay h245-signal
> imp quos disc eve media
>!
>dial-peer voice 2 pots
> preference 2
> destination-pattern 4081234567
> port 2/1
> !
>alias exec co conf to
>alias exec sir she imp route
>alias exec sib she imp into brief
>alias exec sir she run
>alias exec sap she voice pod
>
>
>Neil I
This archive was generated by hypermail 2.1.4 : Thu May 01 2003 - 13:35:52 GMT-3