From: wsqccie@hotnail.com
Date: Mon Apr 07 2003 - 14:23:25 GMT-3
hi, joson
Am I right for your explaitation?
r1 -----R2 , and R2 use dialer map command and r1 without it. and you aslo want dialer watch to work in R1, right? Even R1 dialer watch know the route dispear and how it ininite the call?
----- Original Message -----
From: "Brian Dennis" <brian@5g.net>
To: "'Jason Cash'" <cash2001@swbell.net>; <ccielab@groupstudy.com>
Sent: Monday, April 07, 2003 11:56 AM
Subject: RE: Dialer watch-list not activating
> When using a BRI with dialer map statements it's a multipoint interface.
> This means a mapping is needed. If you are using dialer interfaces or a
> physical BRI interface with a dialer string then it's a point-to-point
> interface and no mappings are needed. The dialer watch feature will call
> using the number configured with the dialer string.
>
> As a side note I'm currently writing a tech article about dialer watch.
> I'll post free for everyone to read in the next couple days.
>
> Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
> Director of CCIE Training and Development - IPexpert, Inc.
> Mailto: brian@ipexpert.net
> Toll Free: 866.225.8064
> Outside U.S. & Canada: 312.321.6924
>
> -----Original Message-----
> From: Jason Cash [mailto:cash2001@swbell.net]
> Sent: Sunday, April 06, 2003 8:41 PM
> To: 'Brian Dennis'; ccielab@groupstudy.com
> Subject: RE: Dialer watch-list not activating
>
> I know that one is needed, but I had it to the the BRI interface on the
> other router 'dialer map ip 65.1.1.2 name r5 broadcast 4081111111'.
>
> My logic was that once the router no longer saw the route 172.168.100.5
> 255.255.255.255 in it's route table, it would then dial based on the BRI
> dialer map. I am wrong again!!
>
> -----Original Message-----
> From: Brian Dennis [mailto:brian@5g.net]
> Sent: Sunday, April 06, 2003 10:26 PM
> To: 'Jason Cash'; ccielab@groupstudy.com
> Subject: RE: Dialer watch-list not activating
>
>
> Jason,
> Why do you think the dialer map isn't needed? Turn on "debug dialer
> events" and the router will tell you it can't dial because a dialer map
> or dialer string is not present.
>
> Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
> Director of CCIE Training and Development - IPexpert, Inc.
> Mailto: brian@ipexpert.net
> Toll Free: 866.225.8064
> Outside U.S. & Canada: 312.321.6924
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Jason Cash
> Sent: Sunday, April 06, 2003 7:23 PM
> To: ccielab@groupstudy.com
> Subject: Dialer watch-list not activating
>
> For some reason, my dialer watch-list is not activating the ISDN link. I
> believe I have it setup correctly and I am seeing the watch route
> removed from the route table.
>
> I can resolve this by adding 'dialer map ip 172.168.100.5 name r5
> broadcast 4081111111' but the need for a dialer map of the watched route
> is not necessary correct? Can anyone tell what would keep this from
> coming up? q
>
> hostname r6
> !
> interface BRI0
> bandwidth 32
> ip address 65.1.1.1 255.255.255.0
> encapsulation ppp
> dialer watch-disable 75
> dialer map ip 65.1.1.2 name r5 broadcast 4081111111
> dialer load-threshold 50 outbound
> dialer watch-group 1
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 408222222201
> isdn spid2 408222222202
> ppp authentication chap callin
> ppp chap hostname router6
> ppp chap password 7 045802150C2E
> ppp multilink
> !
> access-list 101 deny ospf any any
> access-list 101 permit ip any any
> dialer watch-list 1 ip 172.168.100.5 255.255.255.255 dialer-list 1
> protocol ip list 101
>
> Here is the route table before I shut it:
>
> r6#si
> Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
> E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS
> inter area
> * - candidate default, U - per-user static route, o - ODR
> P - periodic downloaded static route
>
> Gateway of last resort is not set
>
> 137.50.0.0/24 is subnetted, 1 subnets
> O 137.50.50.0 [110/3134] via 172.168.100.3, 00:00:39, Serial1
> 65.0.0.0/24 is subnetted, 1 subnets
> C 65.1.1.0 is directly connected, BRI0
> 172.168.0.0/16 is variably subnetted, 5 subnets, 2 masks
> O IA 172.168.30.0/24 [110/1563] via 172.168.100.3, 00:00:40, Serial1
> C 172.168.60.0/24 is directly connected, Ethernet0
> C 172.168.100.0/24 is directly connected, Serial1
> O 172.168.100.3/32 [110/1562] via 172.168.100.3, 00:00:40, Serial1
> O 172.168.100.5/32 [110/3124] via 172.168.100.3, 00:00:41, Serial1
> O E1 160.0.0.0/4 [110/3144] via 172.168.100.3, 00:00:41, Serial1 r6#conf
> t Enter configuration commands, one per line. End with CNTL/Z.
> r6(config)#int s1 r6(config-if)#shut r6(config-if)#
> 3d00h: %OSPF-5-ADJCHG: Process 1, Nbr 172.168.100.3 on Serial1 from FULL
> to DOWN, Neighbor Down: Interface down or detached
> 3d00h: %OSPF-5-ADJCHG: Process 1, Nbr 172.168.200.5 on Serial1 from INIT
> to DOWN, Neighbor Down: Interface down or detached
> 3d00h: %LINK-5-CHANGED: Interface Serial1, changed state to
> administratively down
> 3d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed
> state to down r6(config-if)#^Z
>
> r6#sh ip ro
> Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
> E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS
> inter area
> * - candidate default, U - per-user static route, o - ODR
> P - periodic downloaded static route
>
> Gateway of last resort is not set
>
> 65.0.0.0/24 is subnetted, 1 subnets
> C 65.1.1.0 is directly connected, BRI0
> 172.168.0.0/24 is subnetted, 1 subnets
> C 172.168.60.0 is directly connected, Ethernet0
>
> r6#sh idn stat
> 3d00h: %SYS-5-CONFIG_I: Configured from console by consoles Global ISDN
> Switchtype = basic-ni ISDN BRI0 interface
> dsl 0, interface ISDN Switchtype = basic-ni
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 66, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> TEI = 67, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> TEI 66, ces = 1, state = 5(init)
> spid1 configured, no LDN, spid1 sent, spid1 valid
> Endpoint ID Info: epsf = 0, usid = 0, tid = 3
> TEI 67, ces = 2, state = 5(init)
> spid2 configured, no LDN, spid2 sent, spid2 valid
> Endpoint ID Info: epsf = 0, usid = 0, tid = 7
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Active dsl 0 CCBs = 0
> The Free Channel Mask: 0x80000003
> Number of L2 Discards = 0, L2 Session ID = 15
> Total Allocated ISDN CCBs = 0
This archive was generated by hypermail 2.1.4 : Thu May 01 2003 - 13:35:48 GMT-3