From: folivore (folivore@hotmail.com)
Date: Mon Mar 10 2003 - 13:45:08 GMT-3
Have you ever tried it with 802.1q trunk?
I haven't tried it on ISL yet, but for 802.1q the IRB just doesn't work out
that easy as paper says.
----- Original Message -----
From: "Jung, Jin" <jin.jung@lmco.com>
To: "Vickie Choy" <choyvick@cisco.com>; <ccielab@groupstudy.com>
Sent: Monday, March 10, 2003 7:12 AM
Subject: RE: Question on 3550
> Hi Vicky,,
>
> First for the below question,
> Yes, you have to put
> Bridge 1 route ip
> Bridge irb
> And bridge group 1 on all the bridged interface.
> And BVI config as well,,
>
> Don't forget to create a two sub interface on R2 for each vlan and define
> encapsulation..
>
>
>
> -- Vicky, can you send me your config?
>
>
> -----Original Message-----
> From: Janto Cin [mailto:jantocin@datacomm.co.id]
> Sent: Monday, March 10, 2003 8:00 AM
> To: OhioHondo; Vickie Choy; 'Jung, Jin'; 'Bob Usa'; trust.hogo@sarcom.com;
> jhays@jtan.com; ccielab@groupstudy.com
> Subject: Re: Question on 3550
>
>
> If we use IRB, should we add 'bridge 1 route ip'?
>
> ----- Original Message -----
> From: "OhioHondo" <ohiohondo@columbus.rr.com>
> To: "Vickie Choy" <choyvick@cisco.com>; "'Jung, Jin'" <jin.jung@lmco.com>;
> "'Bob Usa'" <boby2kusa@hotmail.com>; <trust.hogo@sarcom.com>;
> <jhays@jtan.com>; <ccielab@groupstudy.com>
> Sent: Monday, March 10, 2003 7:12 PM
> Subject: RE: Question on 3550
>
>
> > How about this? I think you want to use the 3550 as a router.
> >
> > Define IRB on the 3550.
> > Define port3 and port4 and port 2 as a bridge group.
> > Define a BVI Interface on the 3550 for that bridge group -- give that
> > BVI interface an IP address in the 140.10.1.0/24 subnet. This can
> > serve as the management interface. Give router 2 an IP address in the
> > 140.10.1.0/24 subnet.
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > Vickie Choy
> > Sent: Monday, March 10, 2003 6:20 AM
> > To: 'Jung, Jin'; 'Bob Usa'; trust.hogo@sarcom.com; jhays@jtan.com;
> > ccielab@groupstudy.com
> > Subject: RE: Question on 3550
> >
> >
> > Hi Jung,
> >
> > The BVI interface on R2 works fine if R2 are in the same vlan as R4
> > and R6. But R2 is in the default vlan and R4 and R6 are in vlan 10.
> > I have also tried to put the BVI int in 141.10.9.6 255.255.255.0 and
> > create a int vlan 1 with ip address 141.10.9.7 255.255.255.0 on 3550.
> > But I cannot ping from R2 to 141.10.8.7 which is the IP of int vlan
> > 10.
> >
> > Grateful if you shed some lights on the problem.
> >
> > Vickie
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> > Of Jung, Jin
> > Sent: Monday, March 03, 2003 10:08 PM
> > To: 'Bob Usa'; trust.hogo@sarcom.com; jhays@jtan.com;
> > choyvick@cisco.com; ccielab@groupstudy.com
> > Subject: RE: Question on 3550
> >
> >
> > I think this is IRB question,
> > You do not have to put IP addres on interface of R2, just create a BVI
> > interface on r2 and setup up IRB, BVI will provide Layer 3 routing
> > function.
> >
> >
> > Jin jung...
> >
> >
> >
> > -----Original Message-----
> > From: Bob Usa [mailto:boby2kusa@hotmail.com]
> > Sent: Saturday, March 01, 2003 2:35 AM
> > To: trust.hogo@sarcom.com; jhays@jtan.com; choyvick@cisco.com;
> > ccielab@groupstudy.com
> > Subject: RE: Question on 3550
> >
> >
> > Trunking the port will not make one subnet ping the other subnet
> > without
> >
> > layer three. trunking is a layer 2 protocol that allows a single port
> > to propagate traffic from different vlans. The packets are still in
> > different
> > vlan identified by the vlan tag in the trunk encapsulation. So you've
> > bridge the two vlans (bridge-groups) in R2 you still don't have an ip to
> >
> > ping. Layer 3 connectivity needs layer 3 address.
> >
> >
> >
> >
> >
> >
> > >From: trust.hogo@sarcom.com
> > >Reply-To: trust.hogo@sarcom.com
> > >To: jhays@jtan.com, choyvick@cisco.com, ccielab@groupstudy.com
> > >Subject: RE: Question on 3550
> > >Date: Fri, 28 Feb 2003 14:17:05 -0500
> > >
> > >Remember r2 has no IP address. That's the key to the question and I
> > >don't think the question requires you to put an IP on r2 interface
> > >connecting to port 2. I see it as 2 Vlans assigned the same subnet.
> > >The
> >
> > >only way is to configure a trunk on r2 interface and create 2
> > >subinterfaces belonging to vlan1 and vlan2 and then bridge these two.
> > >
> > >Just thinking aloud I guess.
> > >
> > >-----Original Message-----
> > >From: Jonathan V Hays [mailto:jhays@jtan.com]
> > >Sent: Friday, February 28, 2003 12:24 PM
> > >To: 'Vickie Choy'; ccielab@groupstudy.com
> > >Subject: RE: Question on 3550
> > >
> > >
> > >Once you assign an IP address to a VLAN you can start thinking of the
> > >L3 switch as a many-ported router. The switch can route between the
> > >default vlan (vlan 1) and vlan 10 as follows:
> > >
> > >R4 140.10.1.4 (vlan 10)
> > >R6 140.10.1.6 (vlan 10)
> > >int vlan 10 140.10.1.7 (vlan 10)
> > > **switch routes between vlan 10 and vlan1**
> > >int vlan 1 140.11.12.7 (vlan 1)
> > >R2 140.11.12.2 (vlan 1)
> > >
> > >Here's the relevant link in the 3550 documentation.
> > >
> > >http://www.cisco.com/univercd/cc/td/doc/product/lan/c3550/12112cea/35
> > >50
> > >s
> > >cg/swint.htm#xtocid23
> > >
> > >
> > > > -----Original Message-----
> > > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> > > > Behalf Of Vickie Choy
> > > > Sent: Friday, February 28, 2003 5:35 AM
> > > > To: ccielab@groupstudy.com
> > > > Subject: Question on 3550
> > > >
> > > >
> > > > Hi all,
> > > > -------------------------------
> > > > R4-------| port 4 port 2 |-----------R2
> > > > | 3550 |
> > > > R6-------| port 6 |
> > > > -----------------------------------
> > > >
> > > > Port 4 and port 6 belong to the same vlan vlan 10. Port 2 belong
> > > > to default vlan. Port 4 and 6 belong to the subnet 140.10.1.0/24,
> > > > R4 has 140.10.1.4/24 and R6 has 140.10.1.6/24 on the Ethernet
> > > > interface. R2 has no IP address on the interface.
> > > >
> > > > Question is to create a command interface 140.10.1.7 on 3550 so
> > > > that R2, R4 and R6 be able to ping to that interface.
> > > >
> > > > If I create a SVI "int vlan 10" with ip address 140.10.1.7 only R4
> > > > and R6 can ping. If I configure an ip address say 140.11.12/24 on
> > > > the interface of R2, but is not allowed to configured a static
> > > > route
> >
> > > > on R2 to point to the 140.10.1.0/24 subnet. How to get R6 to be
> > > > able to ping to the command interface?
> > > >
> > > > Appreciate your input.
> > > >
> > > > Thanks
> > > >
> > > > Vickie
> >
> >
> > _________________________________________________________________
> > Add photos to your messages with MSN 8. Get 2 months FREE*.
> > http://join.msn.com/?page=features/featuredemail
This archive was generated by hypermail 2.1.4 : Sat Apr 05 2003 - 08:51:36 GMT-3