From: Hunt Lee (ciscoforme3@yahoo.com.au)
Date: Thu Mar 06 2003 - 11:26:46 GMT-3
Hi Jeff,
That's what I'm confused about. On my VoFR setup, I see the first case even if I
administratively shutdown the outgoing Serial interface (i was expecting that to
fail)... but it didn't
Hunt
--- Jeff Kesemeyer <jkesemey@bellsouth.net> wrote: > Test voice using the
undocumented CSIM command.
> If you see "csim err csim Disconnected recvd DISC" you know the call
> failed.
>
> Successful Call
> r2# csim start 7777
> csim: called number = 7777, loop count = 1 ping count = 0
> csim: loop = 1, failed = 1
> csim: call attempted = 1, setup failed = 1, tone failed = 0
>
> Unsuccessful Call
> r2# csim start 7777
> csim: called number = 7777, loop count = 1 ping count = 0
> csim err csim Disconnected recvd DISC cid(9)
> csim: loop = 1, failed = 1
> csim: call attempted = 1, setup failed = 1, tone failed = 0
>
>
> HTH,
>
> Jeff Kesemeyer
> CCNP, CCDP, MCSE, CNE
> www.bradshawlabs.com
> "Your CCIE Rack Rental Source"
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Hunt Lee
> Sent: Thursday, March 06, 2003 6:08 AM
> To: ccielab@groupstudy.com
> Subject: Voice testing, please help
>
>
> Does anyone know how to test Voice without phones?
>
> RTA--RTB--RTC
>
> where RTB is acting as a Frame Switch.
>
> RTA:-
>
> interface Serial0/0
> ip address 150.50.10.1 255.255.255.0
> encapsulation frame-relay
> no fair-queue
> clockrate 64000
> frame-relay map ip 150.50.10.2 200 broadcast
>
> dial-peer voice 1 pots
> destination-pattern 1111
> port 1/0/0
> !
> dial-peer voice 2 vofr
> destination-pattern 2222
> session target Serial0/0 200
>
> ---
>
> As for RTC:-
>
> interface Serial0/0
> ip address 150.50.10.2 255.255.255.0
> encapsulation frame-relay
> no fair-queue
> clockrate 64000
> frame-relay map ip 150.50.10.1 100 broadcast
>
> dial-peer voice 1 pots
> destination-pattern 2222
> port 1/0/0
> !
> dial-peer voice 2 vofr
> destination-pattern 1111
> session target Serial0/0 100
> !
>
> And I thought I could test the voice setup by "csim start" command.
>
> However, I'm not sure what is meant by the below output... does it means
> that it is working?
>
> R2#ping 150.50.10.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 150.50.10.1, timeout is 2 seconds:
> !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max =
> 56/56/60 ms
>
> R2#csim start 1111
> csim: called number = 1111, loop count = 1 ping count = 0
>
> csim: loop = 1, failed = 1
> csim: call attempted = 1, setup failed = 1, tone failed = 0
>
> R2#
>
>
> What I'm not sure is even when I admin shutdown the Serial interface, it
> still has exactly the same output.
>
> Thanks in advance,
>
> Best Regards,
> Hunt
>
>
>
> http://mobile.yahoo.com.au - Yahoo! Mobile
> - Check & compose your email via SMS on your Telstra or Vodafone mobile.
>
http://mobile.yahoo.com.au - Yahoo! Mobile
- Check & compose your email via SMS on your Telstra or Vodafone mobile.
This archive was generated by hypermail 2.1.4 : Sat Apr 05 2003 - 08:51:33 GMT-3