From: Brian Dennis (brian@labforge.com)
Date: Thu Feb 27 2003 - 23:24:46 GMT-3
Normally you aren't processing IP on the major interface if you are
using sub-interfaces so anything relating to split-horizon on the major
interface has nothing to do with the sub-interface.
Rack4R3#sho ip int | include (Serial)|(Split)
Serial1/0 is up, line protocol is up
Serial1/0.32 is up, line protocol is up
Split horizon is enabled
Serial1/0.243 is up, line protocol is up
Split horizon is enabled
Rack4R3#sho ip int s1/0
Serial1/0 is up, line protocol is up
Internet protocol processing disabled
Rack4R3#
Brian Dennis, CCIE #2210 (R&S/ISP Dial/Security)
brian@labforge.com
http://www.labforge.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
OhioHondo
Sent: Thursday, February 27, 2003 5:36 PM
To: Hunt Lee; 'Jim Brown'
Cc: ccielab@groupstudy.com
Subject: RE: Split-horizon mystery
Hunt/Jim
I believe that split horizon on an interface works for the entire MAJOR
interface. If you have applied split horizon applied to an interface it
applies to all of the sub-interfaces on that MAJOR interface.
I know that you can apply "ip split eirgp xx" directly on a
sub-interface,
but does it then only apply to that sub-interface?
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Hunt Lee
Sent: Thursday, February 27, 2003 6:10 PM
To: 'Jim Brown'
Cc: 'ccielab@groupstudy.com'
Subject: RE: Split-horizon mystery
Hi Jim,
That's kinds of fall into what I was thinking... hence the answer to my
lab
scenario would be wrong?? Since the EIGRP is only running on a
point-to-point network here?
Or am I completely off?
Thanks in advance,
Regards,
Hunt
-----Original Message-----
From: Jim Brown [mailto:Jim.Brown@caselogic.com]
Sent: Friday, 28 February 2003 1:48 AM
To: Hunt Lee; ccielab@groupstudy.com
Subject: RE: Split-horizon mystery
Think about what split horizon is....
Split horizon basically keeps a router from advertising a route out the
interface it learned the route from. Most of the time this is the
desired behavior, but in the case of a multipoint interface it might not
be.
If the spokes are advertising routes to the hub and the hub has split
horizon enabled, it will not advertise routes from one spoke to another
if they are on the same interface.
Split horizon only affects DV protocols and to disable it for EIGRP you
must use a different command than other DV protocols. The command is no
ip split-horizon eigrp <AS> while all other DV protocols us the command
no ip split-horizon.
You can also use show ip interface to determine the status of split
horizon on an interface.
-----Original Message-----
From: Hunt Lee [mailto:huntl@webcentral.com.au]
Sent: Thursday, February 27, 2003 12:20 AM
To: 'ccielab@groupstudy.com'
Subject: Split-horizon mystery
Hi Group,
Does anyone know when one should use "ip split-horizon" for EIGRP?
RTD
/
RTA---- RTB
\
RTC
RTA, RTB & RTD are using OSPF, while RTA & RTC are both using EIGRP...
RTA & RTC are point-to-point, while..
RTA, RTB & RTD are point-to-multipoint
On the solutions, I was told that I need to use "ip split-horizon" on
RTC
outgoing interface (to RTA), why??? I thought we only need to use this
command on the hub if it is point-to-multipoint sub-interface...
anyway, here's the config:-
On RTC:-
interface Serial0
ip address 137.20.200.18 255.255.255.240
ip nat outside
encapsulation frame-relay
ip split-horizon <------ Do we need this???
no ip mroute-cache
keepalive 15
no fair-queue
frame-relay lmi-type ansi
router eigrp 10
network 137.20.0.0
no auto-summary
And on RTA:-
interface Serial0.1 multipoint
ip address 137.20.100.34 255.255.255.224
ip ospf network point-to-multipoint
frame-relay de-group 1 502
frame-relay map ip 137.20.100.33 502 broadcast
frame-relay map ip 137.20.100.35 503 broadcast
!
interface Serial0.2 point-to-point
bandwidth 2000
ip address 137.20.200.17 255.255.255.240
frame-relay interface-dlci 504
router eigrp 10
redistribute ospf 10 metric 2000 100 255 1 1500
passive-interface BRI0
passive-interface Ethernet0
passive-interface Serial0.1
passive-interface Serial1
network 137.20.0.0
no auto-summary
no eigrp log-neighbor-changes
Any help / ideas would be greatly appreciated.
Regards,
Hunt
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:38 GMT-3