From: Larry Letterman (lletterm@cisco.com)
Date: Fri Feb 28 2003 - 00:09:30 GMT-3
Here is the info on the 2621 and the 1FE-FX module I have, with the
IOS and etc...
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9S-M), Version 12.2(8)T5, RELEASE SOFTWARE
(f1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 21-Jun-02 21:31 by ccai
Image text-base: 0x80008074, data-base: 0x8158626C
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
System image file is "flash:c2600-ik9s-mz.122-8.T5.bin"
cisco 2621 (MPC860) processor (revision 0x102) with 60416K/5120K bytes of
memor
Slot 1:
Fast-ethernet (FX) Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.0 Board revision F0
Serial number 18843052 Part number 800-03028-02
FRU Part Number: NM-1FE-FX=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 77 01 00 01 1F 85 AC 50 0B D4 02 00 00 00 00
0x30: 78 00 00 00 00 03 03 00 FF FF FF FF FF FF FF FF
Larry Letterman
Network Engineer
Cisco Systems
----- Original Message -----
From: Daniel Garrity
To: Larry Letterman ; Daniel Garrity ; ccie@rivancitadel.com ; Michael J.
Doherty ; Chuck Church ; Darvin ; ccielab@groupstudy.com
Sent: Thursday, February 27, 2003 6:20 PM
Subject: RE: 1fe2w
That's odd. I tried to get a NM-1FE-TX to trunk on a 2610 and a 2621
with no errors, but it would not pass packets. I opened a TAC case and
was shipped a replacement mod. It also did not work. After further
discussions with the Cisco SE, it was discovered that the NM-1FE-TX was
not compatable with any 2600 router.
I was running 12.1 IOS at the time. Now with 12.2 you can trunk on a
10MB port, so maybe they also addressed the trunking issues on the
NM-1FE mod as well.
Dan
-----Original Message-----
From: Larry Letterman [mailto:lletterm@cisco.com]
Sent: Thursday, February 27, 2003 5:40 PM
To: Daniel Garrity; ccie@rivancitadel.com; Michael J. Doherty; Chuck
Church; Darvin; ccielab@groupstudy.com
Subject: Re: 1fe2w
My 1FE-FX works on the 2621 just fine and does all the trunking okay...
Larry Letterman
Network Engineer
Cisco Systems
----- Original Message -----
From: Daniel <mailto:ccie@garrityfamily.com> Garrity
To: ccie@rivancitadel.com <mailto:ccie@rivancitadel.com> ; Michael J.
<mailto:Z0rand3r@hotmail.com> Doherty ; Chuck Church
<mailto:ccie8776@rochester.rr.com> ; Darvin
<mailto:darvin@blueyonder.co.uk> ; ccielab@groupstudy.com
<mailto:ccielab@groupstudy.com>
Sent: Thursday, February 27, 2003 2:07 PM
Subject: RE: 1fe2w
While the NM-1FE-TX will appear to work on the 2600 platforms. You will
run into issues when doing things like ISL trunking.
Dan
-----Original Message-----
From: ccie@rivancitadel.com <mailto:ccie@rivancitadel.com>
[mailto:ccie@rivancitadel.com]
Sent: Thursday, February 27, 2003 10:01 AM
To: 'Michael J. Doherty'; 'Chuck Church'; 'Darvin';
ccielab@groupstudy.com <mailto:ccielab@groupstudy.com>
Subject: RE: 1fe2w
That isn't exactly correct. I have a 2621 with a NM-1FE-TX in it and
running fine. I haven't been able to get the NM-1FE-2CT1-CSU to run in
any of my 2600's though.
Russ
Russell A. Nelson, CISSP, CCDP, CCNP, CCDA, CCNA, MCSE
Senior Data Architect/Lead Network Engineer
Trinnix, LLC.
Office: 919.367.9915
Cell: 919.412.6111
Email: ranelson@trinnix.com <mailto:ranelson@trinnix.com>
-----Original Message-----
From: nobody@groupstudy.com <mailto:nobody@groupstudy.com>
[mailto:nobody@groupstudy.com] On Behalf Of
Michael J. Doherty
Sent: Thursday, February 27, 2003 11:25 AM
To: Chuck Church; Darvin; ccielab@groupstudy.com
<mailto:ccielab@groupstudy.com>
Subject: Re: 1fe2w
The card is not supported in the 26xx series...the 26xx can only support
two
FE interfaces, and only if they are hardwired to the board, it does not
support any of the FE NMs.
HTH
Mike
----- Original Message -----
From: "Chuck Church" < ccie8776@rochester.rr.com
<mailto:ccie8776@rochester.rr.com> >
To: "Darvin" < darvin@blueyonder.co.uk <mailto:darvin@blueyonder.co.uk>
>; < ccielab@groupstudy.com <mailto:ccielab@groupstudy.com> >
Sent: Thursday, February 27, 2003 10:06
Subject: Re: 1fe2w
> Darvin,
>
> Did you go through the Software Advisor to match your hardware to
an
> image? 12.2 mainline should support that card, however. Are you sure
that
> card is in slot 1? Here's the link for the SW Advisor. Are you sure
that
> card is supported in the 2600 and 3620?
> http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl
<http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl>
>
> Chuck Church
> CCIE #8776, MCNE, MCSE
>
>
> ----- Original Message -----
> From: "Darvin" < darvin@blueyonder.co.uk
<mailto:darvin@blueyonder.co.uk> >
> To: < ccielab@groupstudy.com <mailto:ccielab@groupstudy.com> >
> Sent: Thursday, February 27, 2003 7:47 AM
> Subject: 1fe2w
>
>
> > hi group again
> >
> > i got another issus with nm1fe2w this was taken out of cisco 3640.
> putting
> > it in cisco 2600 aND 3620 and blasted things are not being
recognised by
> the
> > ios images put in 12.2 enterprise, ip only, ip and still not working
i
> > getting this again 00:00:05: %PA-2-UNDEFPA: Undefined Port Adaptor
type
> 215
> > in bay 1
> >
> > any ideas
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:38 GMT-3