From: Larry Letterman (lletterm@cisco.com)
Date: Thu Feb 27 2003 - 22:39:47 GMT-3
My 1FE-FX works on the 2621 just fine and does all the trunking okay...
Larry Letterman
Network Engineer
Cisco Systems
----- Original Message -----
From: Daniel Garrity
To: ccie@rivancitadel.com ; Michael J. Doherty ; Chuck Church ; Darvin ;
ccielab@groupstudy.com
Sent: Thursday, February 27, 2003 2:07 PM
Subject: RE: 1fe2w
While the NM-1FE-TX will appear to work on the 2600 platforms. You will
run into issues when doing things like ISL trunking.
Dan
-----Original Message-----
From: ccie@rivancitadel.com [mailto:ccie@rivancitadel.com]
Sent: Thursday, February 27, 2003 10:01 AM
To: 'Michael J. Doherty'; 'Chuck Church'; 'Darvin';
ccielab@groupstudy.com
Subject: RE: 1fe2w
That isn't exactly correct. I have a 2621 with a NM-1FE-TX in it and
running fine. I haven't been able to get the NM-1FE-2CT1-CSU to run in
any of my 2600's though.
Russ
Russell A. Nelson, CISSP, CCDP, CCNP, CCDA, CCNA, MCSE
Senior Data Architect/Lead Network Engineer
Trinnix, LLC.
Office: 919.367.9915
Cell: 919.412.6111
Email: ranelson@trinnix.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Michael J. Doherty
Sent: Thursday, February 27, 2003 11:25 AM
To: Chuck Church; Darvin; ccielab@groupstudy.com
Subject: Re: 1fe2w
The card is not supported in the 26xx series...the 26xx can only support
two
FE interfaces, and only if they are hardwired to the board, it does not
support any of the FE NMs.
HTH
Mike
----- Original Message -----
From: "Chuck Church" <ccie8776@rochester.rr.com>
To: "Darvin" <darvin@blueyonder.co.uk>; <ccielab@groupstudy.com>
Sent: Thursday, February 27, 2003 10:06
Subject: Re: 1fe2w
> Darvin,
>
> Did you go through the Software Advisor to match your hardware to
an
> image? 12.2 mainline should support that card, however. Are you sure
that
> card is in slot 1? Here's the link for the SW Advisor. Are you sure
that
> card is supported in the 2600 and 3620?
> http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl
>
> Chuck Church
> CCIE #8776, MCNE, MCSE
>
>
> ----- Original Message -----
> From: "Darvin" <darvin@blueyonder.co.uk>
> To: <ccielab@groupstudy.com>
> Sent: Thursday, February 27, 2003 7:47 AM
> Subject: 1fe2w
>
>
> > hi group again
> >
> > i got another issus with nm1fe2w this was taken out of cisco 3640.
> putting
> > it in cisco 2600 aND 3620 and blasted things are not being
recognised by
> the
> > ios images put in 12.2 enterprise, ip only, ip and still not working
i
> > getting this again 00:00:05: %PA-2-UNDEFPA: Undefined Port Adaptor
type
> 215
> > in bay 1
> >
> > any ideas
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:38 GMT-3