From: Sudhanshu Gupta (sudhanshu.gupta@wipro.co.in)
Date: Fri Feb 14 2003 - 04:59:38 GMT-3
team,
you need to use "at" or "in" to schedule it. If you give reload 00:30 or reload 4 it will just reload taking it as a reload command that we normally do.
-sudhanshu
R9#reload in 00:30
System configuration has been modified. Save? [yes/no]:
% Please answer 'yes' or 'no'.
System configuration has been modified. Save? [yes/no]: y
Building configuration...
[OK]
Reload scheduled in 29 minutes
Proceed with reload? [confirm]
R9#
-----Original Message-----
From: Chuck Church [mailto:ccie8776@rochester.rr.com]
Sent: Friday, February 14, 2003 4:10 AM
To: Danny Andaluz andaluz; ccielab@groupstudy.com
Subject: router reload
I had used 'reload 4'. I wonder if the number following can be used to
select the number of the file in flash. In my case, 4 didn't exist. You
using 1 probably loaded the first file. I'll play with it more, see what's
going on.
Chuck Church
CCIE #8776, MCNE, MCSE
----- Original Message -----
From: "Danny Andaluz andaluz" <dannyandaluz@comcast.net>
To: <ccielab@groupstudy.com>
Sent: Thursday, February 13, 2003 3:20 PM
Subject: Re: router reload - undocumented
> I did't get any kind of error. The router just reloaded itself right
> away. It looks as if it ignored the 1 after reload. It reloaded with
> no errors. This is the show version after the reload:
>
> sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-INS-L), Version 12.0(25), RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-2002 by cisco Systems, Inc.
> Compiled Tue 31-Dec-02 12:55 by srani
> Image text-base: 0x0304142C, data-base: 0x00001000
>
> ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a),
> RELEASE
> SOFTW
> ARE (fc1)
>
> r8 uptime is 1 minute
> System restarted by reload
> System image file is "flash:/c2500-ins-l.120-25.bin"
>
> cisco 2500 (68030) processor (revision A) with 4096K/2048K bytes of
> memory.
> Processor board ID 01065031, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> Cisco-ET Extended Temperature platform.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
>
> Configuration register is 0x2102
>
> Looks good to me.
>
> Danny
> CCNP # 1,234,649
>
>
>
>
> >
> >
> > >From: Chuck Church <ccie8776@rochester.rr.com>
> > >Reply-To: Chuck Church <ccie8776@rochester.rr.com>
> > >To: Emad <emad@zakq8.com>, ccielab@groupstudy.com
> > >Subject: Re: router reload - undocumented
> > >Date: Thu, 13 Feb 2003 09:30:16 -0500
> > >
> > >I noticed the same thing. Yesterday during that 'reload in'
> > thread,
> > >someone
> > >mentioned that you could do 'reload x', where x is the number of
> > minutes.>It's not in the docs or CLI help, but it accepted it.
> > Asked if I wanted to
> > >save, and then proceed. But it reloaded immediately. Didn't recover
> > >either. It was a 2611. I was getting 'bad magic file number' or
> > something>like that. Figured my flash was going bad, so I TFTPed,
> > and re-flashed it.
> > >But you had a similar problem. Almost seems like an undocumented
> > command>that sets a flag in the config register or the cookie or
> > something?
> > >Anybody
> > >have an idea?
> > >
> > >Thanks,
> > >
> > >Chuck Church
> > >CCIE #8776, MCNE, MCSE
> > >
> > >
> > >----- Original Message -----
> > >From: "Emad" <emad@zakq8.com>
> > >To: <ccielab@groupstudy.com>
> > >Sent: Thursday, February 13, 2003 7:29 AM
> > >Subject: router reload
> > >
> > >
> > > > While I was working on a router I made a mistake by typing
> > reload 1 ,
> > >then
> > > > the router reloaded but stopped before even decompressing the
> > IOS image
> > > >
> > > > Does anyone know why?
> > > > .
> > >.
> > _________________________________________________________________
> > MSN 8 helps eliminate e-mail viruses. Get 2 months FREE*.
> > http://join.msn.com/?page=features/virus
> .
.
DISCLAIMER:
Information contained and transmitted by this E-MAIL is proprietary to
Wipro Limited and is intended for use only by the individual or entity
to which it is addressed, and may contain information that is privileged,
confidential or exempt from disclosure under applicable law. If this is
a forwarded message, the content of this E-MAIL may not have been sent
with the authority of the Company. If you are not the intended recipient,
an agent of the intended recipient or a person responsible for delivering
the information to the named recipient, you are notified that any use,
distribution, transmission, printing, copying or dissemination of this
information in any way or in any manner is strictly prohibited. If you have
received this communication in error, please delete this mail & notify us
immediately at mailadmin@wipro.co.in
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:22 GMT-3