From: Doug Calton (dcalton@fuse.net)
Date: Wed Feb 12 2003 - 09:40:19 GMT-3
Thanks - I am trying LAM, not MIP. AFAIK, there are no clients for MIP
available, so I have never been able to really test MIP. Anyway, as to your
note that with LAM, I need to configure the ip mobile arp and redistribute
commands on the home network as well, I am surprized, but I will try it. As
for the ip route mobile, I am unclear if this is needed for LAM or not. If
it is not required, I wonder what the redistribute is distributing. Again,
I will test out later today and post results on the newsgroup. Thanks for
the explanation.
----- Original Message -----
From: "P729" <p729@cox.net>
To: "DougAtHome" <dcalton@fuse.net>; "ccielab" <ccielab@groupstudy.com>
Sent: Tuesday, February 11, 2003 9:06 PM
Subject: Re: Problem getting local mobility to work
> First of all, you may want to sort out what you're really trying to
> accomplish: Local Area Mobility (LAM) or Mobile IP (MIP). There appears to
> be fragments of each in your sample config.
>
> The 'ip mobile arp' interface command and the 'redistribute mobile'
routing
> process command in Rtr5 enable LAM on Rtr5. You'll need complementary
> commands on Rtr2 and I believe you'll need to make the subnets contiguous
> (change to /24 masks or re-address one or the other).
>
> The 'router mobile' global command enables MIP, but the rest of a MIP
> configuration appears to be missing (home and foreign agents, etc.). You'd
> also need a MIP client on your host(s) or transparent proxies (like
Aironet
> 350s with the latest code).
>
> Regards,
>
> Mas Kato
> https://ecardfile.com/id/mkato
>
> ----- Original Message -----
> From: "DougAtHome" <dcalton@fuse.net>
> To: "ccielab" <ccielab@groupstudy.com>
> Sent: Tuesday, February 11, 2003 5:33 AM
> Subject: Problem getting local mobility to work
>
>
> I have been trying to get mobile IP to work in a local network. For
> purposes
> of this discussion, the topology is like so:
>
> VLAN11 (170.10.11.0/26) -- Rtr2 -----Frame Relay --Rtr5 -- VLAN34
> (170.10.10.1/26)
>
> Rtr2's VLAN I/F is EIGRP, which redistributes into OSPF (and OSPF into
> EIGRP),
> while the FR ntwk is Area 0 OSPF. VLAN 34 is in area 2.
>
> Full routing in the network is available, no bugs or issues.
>
> I configured a PC with an IP addr of 170.10.11.5/26 (gateway 170.10.11.1,
> which is the Rtr2 I/F), and move it to VLAN 34, but it does not start up
> Router Mobile, nor can I ping anywhere out of the PC. I have installed
the
> commands as I understand from Cisco documentation, but no soap. Does any
> one
> have a working config or a link showing this with an example?
>
> Following is my current config of Rtr5, if needed. TIA!
>
> hostname Rtr5
> enable secret 5 $1$16B7$XA9fx4lFw2T3sLiXSzjqy1
> clock timezone EST -5
> clock summer-time EDT recurring
> ip subnet-zero
> no ip domain-lookup
> ip audit notify log
> ip audit po max-events 100
> ip ssh time-out 120
> ip ssh authentication-retries 3
> call rsvp-sync
> interface Loopback0
> ip address 170.10.5.1 255.255.255.0
> ip ospf network point-to-point
> interface Ethernet0/0
> ip address 170.10.10.2 255.255.255.192
> ip mobile arp access-group 10
> ip ospf authentication
> ip ospf authentication-key xxxxxx
> ip ospf message-digest-key 1 md5 xxxxxxxx
> half-duplex
> interface Serial0/0
> ip address 170.10.8.5 255.255.255.240
> encapsulation frame-relay
> ip ospf message-digest-key 1 md5 xxxxxxx
> ip ospf network point-to-multipoint
> no fair-queue
> frame-relay interface-dlci 52
> frame-relay interface-dlci 53
> no frame-relay inverse-arp
> interface Ethernet0/1
> no ip address
> shutdown
> half-duplex
> router mobile
> distance 80
> router ospf 1
> log-adjacency-changes
> area 0 authentication message-digest
> area 0 range 170.10.8.0 255.255.255.0
> area 2 range 170.10.10.0 255.255.255.0 cost 54
> area 2 virtual-link 170.10.7.1 message-digest-key 1 md5 xxxxxxx
> redistribute mobile metric 54 subnets
> network 170.10.5.1 0.0.0.0 area 2
> network 170.10.8.5 0.0.0.0 area 0
> network 170.10.10.2 0.0.0.0 area 2
> ip classless
> ip http server
> access-list 10 permit 170.10.11.0 0.0.0.192
> dial-peer cor custom
> line con 0
> session-timeout 60
> exec-timeout 60 0
> password xxxxx
> login
> line aux 0
> line vty 0 4
> session-timeout 60
> exec-timeout 60 0
> password xxxxx
> login
> line vty 5 15
> login
> ntp authentication-key 1 md5 xxxxxxxx
> ntp authenticate
> ntp trusted-key 1
> ntp clock-period 17208130
> ntp server 170.10.9.1
> end
> .
.
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:19 GMT-3