From: Nelson Herron (nelsonrherron@earthlink.net)
Date: Thu Feb 06 2003 - 23:51:48 GMT-3
That's not quite true. I have done this for over a year now with a 4500 and
an RSP7000. Found the original on eBay of all places. Nelson Herron
----- Original Message -----
From: "Richard Davidson" <rich@myhomemail.net>
To: "Casey, Paul (6822)" <Paul.Casey@o2.com>; "'Yinka Daramola'"
<o_daramola@hotmail.com>; "'Amlendu Kumar'" <amlendu_kumar@hotmail.com>
Cc: <ccielab@groupstudy.com>
Sent: Thursday, February 06, 2003 5:26 PM
Subject: RE: Trunk on 10mb
> Wow I didn't know that. It's not avalable until 12.2
> so I don't think they can test on that yet. Probably
> isn't much different than fastE.
>
> Overview
> 802.1Q encapsulation is now available on the built-in
> 10BaseT Ethernet interfaces of the Cisco 2610, 2611,
> and 2612 with Cisco IOS software 12.2(2)T and
> subsequent releases. Although this feature has been
> available on the Cisco 2600/3600 series since the
> release of Cisco IOS 12.1(5)T, support was previously
> limited to Fast Ethernet interfaces only. 802.1Q is
> not supported on any other Cisco 2600/3600 series
> 10BaseT Ethernet interface. Table 1 shows the
> 2600/3600 series chassis and modules that support
> 802.1Q:
>
>
> --- "Casey, Paul (6822)" <Paul.Casey@o2.com> wrote:
> > 802.1q trunking Works for 10mb/s interfaces check
> > out following link (watch
> > wordwrap)
> > Supported on some 2600/3600 series routes.
> >
> > Dunno know if Cisco advertise this openly but here
> > is the link on there web
> > site.
> > You need an account to view.
> >
> >
> > Enjoy.
> > Kind regards.
> > Paul.
> >
> >
> >
>
http://www.cisco.com/en/US/customer/products/hw/routers/ps259/prod_bulletin0
> > 9186a00800921e4.html
> >
> >
> >
> > -----Original Message-----
> > From: Yinka Daramola [mailto:o_daramola@hotmail.com]
> >
> > Sent: 06 February 2003 23:29
> > To: Amlendu Kumar
> > Cc: ccielab@groupstudy.com
> > Subject: Re: Trunk on 10mb
> >
> >
> > Thanks Amlendu. I'll check the documentation for a
> > 2924.
> >
> > ps: the question was to configure the type of
> > encapsulation that would work
> > on a 10mb port, on a fastethernet port.
> >
> > Yinka
> >
> > ----- Original Message -----
> > From: "Amlendu Kumar" <amlendu_kumar@hotmail.com>
> > To: "Yinka Daramola" <o_daramola@hotmail.com>
> > Sent: Thursday, February 06, 2003 3:30 PM
> > Subject: Re: Trunk on 10mb
> >
> >
> > > Hi Yinka
> > >
> > > No trunking works below 100 mb on 3550
> > > It works on 2924 xl with dot 1q at 10 mb
> > > I have tested this .
> > >
> > > Reagards Amlendu
> > >
> > > ----- Original Message -----
> > > From: "Yinka Daramola" <o_daramola@hotmail.com>
> > > To: <ccielab@groupstudy.com>
> > > Sent: Thursday, February 06, 2003 10:54 PM
> > > Subject: Trunk on 10mb
> > >
> > >
> > > > I'm going through one of iPexpert's 3550 lab and
> > there is a
> > > > requirement
> > to
> > > > configure the only trunk protocol that works on
> > a 10Mb interface.
> > > >
> > > > Is this 802.1Q ? I searched the archives and did
> > not get a
> > > > conclusive
> > > answer.
> > > >
> > > > Does anyone know a specific link that answers
> > the question? What
> > > > IOS
> > code
> > > > supports this?
> > > >
> > > > Thanks.
> > > >
> > > > Yinka Daramola, MCSE, CCNP, RHCE
> > > > Red Hat Inc.
> > > > .
> >
>
****************************************************************************
************
> >
> > This E-mail is from O2. The E-mail and any files
> > transmitted with it are confidential and may also be
> > privileged and intended
> > solely for the use of the individual or entity to
> > whom they are addressed.
> > Any unauthorised direct or indirect dissemination,
> > distribution or copying
> > of this message and any attachments is strictly
> > prohibited. If you have
> > received the E-mail in error please notify
> > postmaster@O2.com or
> > telephone ++ 353 1 6095000.
> >
> >
>
****************************************************************************
*************
> > .
> >
> __________________________________________________________________
> > To unsubscribe from the CCIELAB list, send a message
> > to
> > majordomo@groupstudy.com with the body containing:
> > unsubscribe ccielab
> .
.
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:14 GMT-3