From: Khalid A. Kaseb (khalid_ameen@rayaintegration.com)
Date: Thu Feb 06 2003 - 10:18:14 GMT-3
Distribut-list prefix under the router configuration is working with
prefix-list
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Hunt Lee
Sent: Thursday, February 06, 2003 2:44 PM
To: Brian McGahan; jim.phillipo@guardent.com; ccielab@groupstudy.com
Subject: RE: CyscoExpert lab
Sorry... please ignore my last post. Forget that distribute-list only
works with
Access-List, but not Prefix List.
Cheers,
Lee
--- Hunt Lee <ciscoforme3@yahoo.com.au> wrote: > Hi Brian / Jim,
>
> Thanks so much for the quick reply. After I did a "distance eigrp 95
95", I then
> have the recursive routing problem. I was intented to block off the
150.1.2.0/24
> route from learning via R4's Tunnel interface, but R4 keeps on saying
it is
> learning
> the route from the tunnel int even after I put in the distribute-list
under EIGRP
> process...
>
> interface Tunnel0
> ip address 150.1.24.4 255.255.255.0
> tunnel source Loopback0
> tunnel destination 150.1.2.2
>
> router eigrp 100
> redistribute rip route-map inEIGRP
> passive-interface FastEthernet0/0
> passive-interface Serial0/0
> network 150.1.14.4 0.0.0.0
> network 150.1.24.0 0.0.0.255
> default-metric 1000 1 255 1 1000
> distribute-list BlockTunnel in Tunnel0
> distance eigrp 95 95
> no auto-summary
>
> route-map BlockTunnel permit 10
> match ip address prefix-list PrefixA
>
> ip prefix-list PrefixA deny 150.1.2.2/32
> ip prefix-list PrefixA deny 150.1.2.0/24
> ip prefix-list PrefixA permit 0.0.0.0/0 le 32
>
> Thanks so much for the help in advance,
>
> Cheers,
> Lee
>
>
> --- Brian McGahan <brian@cyscoexpert.com> wrote: > Hunt,
> >
> > You cannot change the distance of External EIGRP on a per prefix
> > basis. Therefore, either you must change the distance of the OSPF
> > prefix as you have done, or change the distance of all External
EIGRP
> > prefixes as Jim has proposed.
> >
> > For your DLSw+ question, yes you need a LLC2 mapping. Since
> > DLSw+ lite uses local acknowledgment, you must provide reliable
> > transport over the WAN. Frame-Relay by itself is not reliable,
> > therefore the extra LLC2 header must be added to ensure reliable
> > transport.
> >
> > HTH
> >
> > Brian McGahan, CCIE #8593
> > Director of Design and Implementation
> > brian@cyscoexpert.com
> >
> > CyscoExpert Corporation
> > Internetwork Consulting & Training
> > Toll Free: 866.CyscoXP
> > Fax: 847.674.2625
> >
> >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
Behalf
> > Of
> > > Hunt Lee
> > > Sent: Wednesday, February 05, 2003 7:19 AM
> > > To: ccielab@groupstudy.com
> > > Subject: CyscoExpert lab
> > >
> > > Hi friends,
> > >
> > > I have some questions about the configuration for Cyscoexpert
Sample
> > lab.
> > >
> > > First: for question 2 under J
> > >
> > > 2. Double check R1, are you missing any routes?
> > >
> > > I got this to work by increasing the Admin Dist. of OSPF route at
R4
> > from
> > > R3
> > >
> > > router ospf 1
> > > distance 180 195.1.3.3 0.0.0.0 1
> > >
> > > However, instead of doing this, if I tried to decrease the Admin
Dist
> > of
> > > EIGRP route
> > > from R2 (via Tunnel). It doesn't work.
> > >
> > > I think it's because R2 actually got the route via OSPF as well,
hence
> > > even now
> > > EIGRP has a lower Admin Dist than OSPF at R4, R2 would have no
EIGRP
> > route
> > > (150.1.30.0/24) for distribute into R4.
> > >
> > > Am I right?
> > >
> > >
> > > Second: for question 3 under H.
> > >
> > > 3. Configure a DLSW+ session between R3 & R4 direct over the
> > Frame-relay
> > > network.
> > >
> > >
> > > I think it has been done by:
> > >
> > > dlsw local-peer peer-id 150.1.4.4
> > > dlsw remote-peer 0 frame-relay interface Serial0/0 403
> > > dlsw bridge-group 1
> > >
> > > Am I right?
> > >
> > > If so, is there any reason why I would need to use frame-relay map
> > llc2
> > > 403
> > > broadcast command? Is this command always required for DLSW Lite
> > config?
> > >
> > >
> > > Thanks so much for the help in advance,
> > >
> > > Cheers,
> > > Lee
> > >
> > > http://movies.yahoo.com.au - Yahoo! Movies
> > > - What's on at your local cinema?
> > > .
> http://greetings.yahoo.com.au - Yahoo! Greetings
> - Send some online love this Valentine's Day.
>
http://greetings.yahoo.com.au - Yahoo! Greetings
- Send some online love this Valentine's Day.
.
.
This archive was generated by hypermail 2.1.4 : Sat Mar 01 2003 - 11:06:11 GMT-3