From: tan (tan@dia.janis.or.jp)
Date: Tue Jan 14 2003 - 19:11:04 GMT-3
Thanks, I was aware debug ip packet detail had outgoing icmps, I was just
curious why debug ip icmp would not. Not a burning issue.
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Matthew Poole
> Sent: Wednesday, January 15, 2003 4:04 AM
> To: ccielab@groupstudy.com
> Cc: Joe Chang; tan
> Subject: Re: lack of output in debug ip icmp
>
>
> For a variation on Joe Changs post you could add detail to
> the debug, this
> will show your ICMP going out.
>
> R9#ping 10.1.1.1
>
>
> Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max =
> 28/30/32 ms
> R9#
> 4d08h: IP: s=10.1.1.2 (local), d=10.1.1.1 (Serial0), len 100, sending
> 4d08h: ICMP type=8, code=0
> 4d08h: IP: s=10.1.1.1 (Serial0), d=10.1.1.2 (Serial0), len 100, rcvd 3
> 4d08h: ICMP type=0, code=0
> 4d08h: IP: s=10.1.1.2 (local), d=10.1.1.1 (Serial0), len 100, sending
> 4d08h: ICMP type=8, code=0
> 4d08h: IP: s=10.1.1.1 (Serial0), d=10.1.1.2 (Serial0), len 100, rcvd 3
> 4d08h: ICMP type=0, code=0
> 4d08h: IP: s=10.1.1.2 (local), d=10.1.1.1 (Serial0), len 100, sending
> 4d08h: ICMP type=8, code=0
>
> ----- Original Message -----
> From: "Joe Chang" <changjoe@earthlink.net>
> To: <ccielab@groupstudy.com>
> Sent: Thursday, January 09, 2003 3:20 AM
> Subject: Re: lack of output in debug ip icmp
>
>
> > To debug outgoing ip packets you could try this:
> >
> > access-list 100 permit icmp any any
> > debug ip packet 100
> >
> >
> > ----- Original Message -----
> > From: "Joe" <groupstudy@comcast.net>
> > To: "'tan'" <tan@dia.janis.or.jp>; "'Ccielab (E-mail)'"
> > <ccielab@groupstudy.com>
> > Sent: Wednesday, January 08, 2003 11:27 PM
> > Subject: RE: lack of output in debug ip icmp
> >
> >
> > > Sometimes you gotta disable fast switching.
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] On Behalf Of
> > > tan
> > > Sent: Wednesday, January 08, 2003 5:39 AM
> > > To: Ccielab (E-mail)
> > > Subject: OT: lack of output in debug ip icmp
> > >
> > >
> > > Is it normal that typical outgoing pings are not output
> to console under
> > > "debug ip icmp"? Only return pings and other icmp types
> are included,
> > > but not standard echo request. I have been bit a few
> times just assuming
> > > my ping went out and was troubleshooting the return path,
> when it turned
> > > out it never left the router because unroutable. I have found only
> > > "debug ip pack det" will include outgoing ping? I know
> not much can be
> > > done about it, but anyone else find it odd or offer an
> explanation why?
> > > .
> > .
> .
.
This archive was generated by hypermail 2.1.4 : Sat Feb 01 2003 - 07:33:49 GMT-3