From: Nathan Chessin (nchessin@cisco.com)
Date: Sun Jan 12 2003 - 02:20:55 GMT-3
what about the "vofr cisco" command under the interface-dlci command?
Nate
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Rick
> Sent: Saturday, January 11, 2003 6:40 PM
> To: kym blair
> Cc: ccielab@groupstudy.com
> Subject: question about VOFR
>
>
> Kym, or any other VOFR gurus,
>
> Of the below list frame-relay commands. Which one are needed
> to pass data and
> voice... I tried to use only frame-relay voice bandwidth
> 7800, and of course I
> could not ping, but I couldn't call the other phone either..
> I found these
> commands on the CCO and I can ping, but I still can call
> between routers. I
> will attach the configs below.
> What I'm I doing wrong.. I trying to cram as much as possible
> before I go to
> Netmaster NMC-1 at the end of the month... I want to have all
> the basics down
> so I can walk away with the advanced topics...
>
> Thanks,
> Rick
>
> !There are only two routers and a frame switch
>
> Host r6
> interface Serial0/0
> no ip address
> encapsulation frame-relay
> clockrate 2000000
> frame-relay traffic-shaping
> !
> interface Serial0/0.1 point-to-point
> ip address 150.150.10.1 255.255.255.0
> frame-relay interface-dlci 100
> class voice
> !
> map-class frame-relay voice
> frame-relay cir 768000
> frame-relay bc 1000
> frame-relay mincir 120000
> no frame-relay adaptive-shaping
> frame-relay fair-queue
> frame-relay voice bandwidth 78000
> frame-relay fragment 1500
> !
> !
> voice-port 1/0/0
> !
> voice-port 1/0/1
> !
> dial-peer cor custom
> !
> !
> !
> dial-peer voice 1 pots
> destination-pattern 1111
> port 1/0/0
> !
> dial-peer voice 2 vofr
> destination-pattern 2222
> session target Serial0/0 100
>
> Host r11
> interface Serial0/0
> no ip address
> encapsulation frame-relay
> frame-relay traffic-shaping
> frame-relay lmi-type ansi
> !
> interface Serial0/0.1 point-to-point
> ip address 150.150.10.2 255.255.255.0
> frame-relay interface-dlci 200
> class voice
> !
> !
> map-class frame-relay voice
> frame-relay cir 768000
> frame-relay bc 1000
> frame-relay mincir 120000
> no frame-relay adaptive-shaping
> frame-relay fair-queue
> frame-relay voice bandwidth 78000
> frame-relay fragment 1500
> !
> !
> voice-port 1/0/0
> !
> voice-port 1/0/1
> !
> dial-peer cor custom
> !
> !
> !
> dial-peer voice 1 pots
> destination-pattern 2222
> port 1/0/0
> !
> dial-peer voice 2 vofr
> destination-pattern 1111
> session target Serial0/0 200
> !
> !
> !
> QUESIONS: about these commands, which one are nessary? I
> guess I still don't
> no understand the Bc, etc
> map-class frame-relay voice
> frame-relay cir 768000
> frame-relay bc 1000
> frame-relay mincir 120000
> no frame-relay adaptive-shaping
> frame-relay fair-queue
> frame-relay voice bandwidth 78000
> frame-relay fragment 1500
> .
.
This archive was generated by hypermail 2.1.4 : Sat Feb 01 2003 - 07:33:47 GMT-3