From: Geralt Omhof (geralt@OmnIT.nl)
Date: Thu Jan 09 2003 - 06:00:35 GMT-3
Hi,
Does anybody know what cable to use when connecting a 4000M router with a 2500 via it's aux ports? All signals on the 2500 are ok (see below) and on the 4000m all are ok, except the DSR (noDSR).
I checked cco and learned the pin-outs are different, but it's a bit confusing. So I thought maybe somebody on the list tried this before and will save me the trouble of "trial and error"....
2500:
r2#sh li
12:17:05: %SYS-5-CONFIG_I: Configured from console by console
r2#sh line aux 0
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
A 1 AUX 38400/38400 - inout - - - 0 1 0/0 -
Line 1, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 38400/38400, no parity, 2 stopbits, 8 databits
Status: Ready, Active, Async Interface Active, CTS Raised,
Modem Signals Polled
Capabilities: Modem Callout, Modem RI is CD,
Line is permanent async interface
Modem state: Ready
Group codes: 0
Line is running PPP routing.
0 output packets queued, 1 input packets.
Async Escape map is 11111111111111111111111111111111
Modem hardware state: CTS* DSR* DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
00:10:00 never none not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: 00:00:16
Editing is enabled.
History is enabled, history size is 10.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are lat pad v120 mop telnet rlogin udptn nasi.
Allowed output transports are lat pad v120 mop telnet rlogin nasi.
Preferred transport is lat.
No output characters are padded
No special data dispatching characters
r2#
4000M:
r3#sh line aux 0
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
1 AUX 38400/38400 - inout - - - 0 2 0/0 -
Line 1, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 38400/38400, no parity, 2 stopbits, 8 databits
Status: CTS Raised, Modem Signals Polled
Capabilities: Modem Callout, Modem RI is CD,
Line is permanent async interface
Modem state: Idle
Modem hardware state: CTS* noDSR DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
00:10:00 never none not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: never
Editing is enabled.
History is enabled, history size is 10.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are pad v120 telnet.
Allowed output transports are pad v120 telnet.
Preferred transport is telnet.
No output characters are padded
No special data dispatching characters
r3#
What should I do to get this working?
thanks in advance,
Geralt
.
This archive was generated by hypermail 2.1.4 : Sat Feb 01 2003 - 07:33:46 GMT-3