From: Donny MATEO (donny.mateo@sg.ca-indosuez.com)
Date: Wed Jan 08 2003 - 05:20:20 GMT-3
Hi Beda,
i found no problem when I duplicate your configuration. Do make sure that the interface on R1 where
you configure ip igmp join-group a.b.c.d has the statement ip pim sparse-dense-mode.
Cheers.
Donny
beda jain
<bpjain@cisco.com To: "David Ham" <ccieau@hotmail.com>, fingham@cox.net, ccielab@groupstudy.com
> cc: Jing Shi <jishi@cisco.com>, bpjain@cisco.com
Sent by: Subject: Re: Multicast Help!!
nobody@groupstudy
.com
08-01-2003 05:04
Please respond to
beda jain
Hi,
I try the same scenario with little change.
It work fine when every thing is in spare-dense-mode.
r1----ether-----r6-------FR---------r3--------FR------r7---------r2
all are in sparse-dense-mode and use loop back address for rp and rp discovery.
when i put join group in r2 , rp announce in r7 and rp discovery in r3 , i
can ping that join group from all the router and i can see the rp for that
group in all the router.
when i put another join group in r1 i can see the rp in all the router. but
i can ping from r1, r6 and r3 .
BUT i can not ping from r7 and r2.
WHY????
Thanks,
Beda
But when i put a join group in R5 i can ping from
At 10:00 AM 7/15/2002 +1000, David Ham wrote:
>Fred,
>
>As you suggested, I removed ip pim nbma on all frame interfaces and put ip
>pim spare-dense mode on all interface.
>
>Well it works.-- Thanks a lot :)
>
>But when you have frame-relay connection, I thought you should use ip pim
>nbma-mode -- isn't that right??
>
>BTW, where would be the position of "ip pim send-auto-announce" interface
>be ?? -- i put ip pim send-auto-announce s 0.1 scope 15 on R3 -- is this ok ??
>
>
>Here is the R2 mroute table.
>
>R2#sim
>IP Multicast Routing Table
>Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned
> R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT
> M - MSDP created entry, X - Proxy Join Timer Running
> A - Candidate for MSDP Advertisement
>Outgoing interface flags: H - Hardware switched
>Timers: Uptime/Expires
>Interface state: Interface, Next-Hop or VCD, State/Mode
>
>(*, 224.0.1.39), 00:06:18/00:02:59, RP 0.0.0.0, flags: D
> Incoming interface: Null, RPF nbr 0.0.0.0
> Outgoing interface list:
> Serial0, Forward/Sparse-Dense, 00:06:18/00:00:00
>
>(170.150.32.3, 224.0.1.39), 00:02:18/00:00:41, flags: PT
> Incoming interface: Serial0, RPF nbr 170.150.32.3
> Outgoing interface list: Null
>
>(*, 224.0.1.40), 00:07:40/00:00:00, RP 0.0.0.0, flags: DJCL
> Incoming interface: Null, RPF nbr 0.0.0.0
> Outgoing interface list:
> Serial0, Forward/Sparse-Dense, 00:07:40/00:00:00
>
>(170.150.10.4, 224.0.1.40), 00:06:18/00:02:38, flags: PCLT
> Incoming interface: Serial0, RPF nbr 170.150.32.3
> Outgoing interface list: Null
>
>(*, 224.2.2.2), 00:07:41/00:00:00, RP 170.150.32.3, flags: SJPCL
> Incoming interface: Serial0, RPF nbr 170.150.32.3
> Outgoing interface list: Null
>
>(170.150.20.4, 224.2.2.2), 00:00:15/00:02:44, flags: PCLT
> Incoming interface: Serial0, RPF nbr 170.150.32.3
> Outgoing interface list: Null
>
>
>Let me know which ones to look at to know auto-rp is working correctly.
>
>Many Thanks.
>
>Regards,
>
>David Ham
>
>
>>From: "Fred Ingham" <fingham@cox.net>
>>Reply-To: "Fred Ingham" <fingham@cox.net>
>>To: "David Ham" <ccieau@hotmail.com>, <ccielab@groupstudy.com>
>>Subject: Re: Multicast Help!!
>>Date: Sun, 14 Jul 2002 15:58:11 -0400
>>
>>David: If you are using R5 and R6 only as sources of the 224.2.2.2 ping you
>>do not need to enable multicast routing on these routers. Also the nbma
>>mode isn't needed anywhere you have it
>>
>>For auto-rp you need ip pim sparse-dense mode on the R4 s0.1 and s0.2, R3
>>s0.1 and s1, and R2 s0. Clear the mroute tables or reboot after the mode
>>change.
>>
>>Auto-rp uses 224.0.1.39 and 224.0.1.40 for announce and discovery
>>respectively.
>>
>>If you send the R2 mroute table after the mode change I can show you which
>>entries are the ones to look at to know auto-rp is working correctly.
>>
>>Cheers, Fred.
>>
>>
>>
>>
>>
>>
>>----- Original Message -----
>>From: "David Ham" <ccieau@hotmail.com>
>>To: <ccielab@groupstudy.com>
>>Sent: Sunday, July 14, 2002 3:25 AM
>>Subject: Multicast Help!!
>>
>>
>> > Hi all,
>> >
>> > I have multicast question which drive me crazy.
>> >
>> > The scenario is as follows,
>> >
>> >
>> >
>> > R4-s0.1--(FR)----s0.1--R3-s1------s0-R2
>> > |
>> > s0.2
>> > |\
>> > | \
>> > (FR)
>> > | \
>> > s0 s0
>> > R5 R6
>> >
>> >
>> > R4 s0.1 is frame subinterface point-to-point
>> > R4 s0.2 is frame multpoint
>> >
>> > IP connectivity is fine.
>> >
>> > At R2
>> > IP igmp join 224.2.2.2 at serial 0
>> >
>> > I applied
>> > R2 s0, ---- ip pim spare-mode
>> > R3 s1 =ip pim spare-mode, s0.1 = ip pim spare-mode + ip pim nbma-mode
>> > R4 s0.1,s0.2 = ip pim spare-mode + ip pim nbma-mode
>> > R5 s0 = ip pim spare-mode + ip pim nbma-mode
>> > R6 s0 = ip pim spare-mode + ip pim nbma-mode
>> >
>> > I add ip pim send-auto-announce s0.1 scope 15 at R3
>> > and
>> >
>> > add ip pim send-auto-discovery s 0.2 scope 15 at R4
>> >
>> > but I am unable to make ping 224.2.2.2 from R6, R5
>> >
>> >
>> > I manage to work out with static RP but I couln't work out with AUTO-RP
>> >
>> > Anyone have any idea ??
>> >
>> >
>> >
>> >
>> > Regards,
>> > David Ham
>> >
>> >
>> > _________________________________________________________________
>> > MSN Photos is the easiest way to share and print your photos:
>> > http://photos.msn.com/support/worldwide.aspx
>> > _________________________________________________________________
>> > Commercial lab list: http://www.groupstudy.com/list/commercial.html
>> > Please discuss commercial lab solutions on this list.
>>_________________________________________________________________
>>Commercial lab list: http://www.groupstudy.com/list/commercial.html
>>Please discuss commercial lab solutions on this list.
>Regards,
>David Ham
>
>
>_________________________________________________________________
>Send and receive Hotmail on your mobile device: http://mobile.msn.com
>_________________________________________________________________
>Commercial lab list: http://www.groupstudy.com/list/commercial.html
>Please discuss commercial lab solutions on this list.
.
This message is for information purposes only and its content
should not be construed as an offer, or solicitation of an offer,
to buy or sell any banking or financial instruments or services
and no representation or warranty is given in respect of its
accuracy, completeness or fairness. The material is subject
to change without notice. You should take your own independent
tax, legal and other professional advice in respect of the content
of this message. This message may contain confidential or
legally privileged material and may not be copied, redistributed
or published (in whole or in part) without our prior written consent.
This email may have been intercepted, partially destroyed,
arrive late, incomplete or contain viruses and no liability is
accepted by any member of the Credit Agricole Indosuez group
as a result. If you are not the intended recipient of this message,
please immediately notify the sender and delete this message
from your computer.
.
This archive was generated by hypermail 2.1.4 : Sat Feb 01 2003 - 07:33:45 GMT-3