From: Hunt Lee (ciscoforme3@yahoo.com.au)
Date: Sat Dec 28 2002 - 21:39:40 GMT-3
I'm sure this question has been asked a million times, but the archives
aren't giving me the answer I'm looking for. How do you configure DLSw Lite?
PC A -- RTA --- Frame-Relay Switch --- RTB -- PC B
When I initiate traffic by clicking on Network Neighborhood, I can see the MAC
addresses showing up from the "show bridge" command & "show dlsw reachability" & I
can also see the DLSW peers' states as "Connect". Yet the circuit keeps on getting
to the "CKT_START" state (as shown below), then the circuit will disappear, and I
just can't see the other computer via Network Neighborhood.
RTB#sh dlsw circuits
Index local addr(lsap) remote addr(dsap) state uptime
788529156 000a.5d6e.57fa(F0) 000a.209d.a221(F0) CKT_START -
RTB#
And here are some other show outputs...
RTA#sh bridge
Total of 300 station blocks, 298 free
Codes: P - permanent, S - self
Bridge Group 1:
Address Action Interface Age RX count TX count
0050.ba76.ea5f forward DLSw Port0 1 4 0
0050.04b9.4584 forward FastEthernet0/0 0 7 0
RTA#
RTB#sh bridge
Total of 300 station blocks, 298 free
Codes: P - permanent, S - self
Bridge Group 1:
Address Action Interface Age RX count TX count
0050.ba76.ea5f forward Ethernet0 1 4 0
0050.04b9.4584 forward DLSw Port0 0 4 0
RTB#
RTA#sh dlsw peer
Peers: state pkts_rx pkts_tx type drops ckts TCP uptime
LLC2 Se0/0.1 120 CONNECT 174 160 conf 0 0 - 00:46:53
Total number of connected peers: 1
Total number of connections: 1
RTB#sh dlsw peer
Peers: state pkts_rx pkts_tx type drops ckts TCP uptime
LLC2 Se0 121 CONNECT 159 170 conf 0 0 - 00:46:14
Total number of connected peers: 1
Total number of connections: 1
Here are the config for my routers...
For RTA-
dlsw local-peer peer-id 1.1.1.1 promiscuous
dlsw remote-peer 0 frame-relay interface Serial0/0.1 120
dlsw bridge-group 1
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
no ip address
speed 10
half-duplex
bridge-group 1
interface Serial0/0
no ip address
encapsulation frame-relay
no fair-queue
frame-relay lmi-type cisco
!
interface Serial0/0.1 multipoint
ip address 172.16.1.1 255.255.255.0
no ip split-horizon eigrp 2001
frame-relay map llc2 120 broadcast
frame-relay map ip 172.16.1.5 110 broadcast
frame-relay map ip 172.16.1.6 120 broadcast
router eigrp 2001
passive-interface FastEthernet0/0
network 1.0.0.0
network 172.16.0.0
no auto-summary
bridge 1 protocol ieee
As for RTB:-
dlsw local-peer peer-id 3.3.3.3
dlsw remote-peer 0 frame-relay interface Serial0 121
dlsw bridge-group 1
interface Loopback1
ip address 3.3.3.3 255.255.255.255
interface Ethernet0
no ip address
bridge-group 1
interface Serial0
ip address 172.16.1.6 255.255.255.0
encapsulation frame-relay
no fair-queue
clockrate 64000
frame-relay map llc2 121 broadcast
frame-relay map ip 172.16.1.5 121 broadcast
frame-relay map ip 172.16.1.1 121 broadcast
no frame-relay inverse-arp
router eigrp 2001
network 3.0.0.0
network 172.16.0.0
no auto-summary
no eigrp log-neighbor-changes
bridge 1 protocol ieee
Did I do anything wrong???
Any comments would be greatly appreciated.
.
http://movies.yahoo.com.au - Yahoo! Movies
- What's on at your local cinema?
.
This archive was generated by hypermail 2.1.4 : Fri Jan 17 2003 - 17:21:54 GMT-3