From: Peter (peter@cyscoexpert.com)
Date: Tue Dec 24 2002 - 19:04:56 GMT-3
Jason,
LS1010 is used to set up an ATM cloud, meaning that on major interfaces you
set up static PVCs and switch them appropriately. LS1010 with ASP is a layer
2 device and switches cells, unless you have an ARM card (I believe this is
the name) then you can route at layer 3 as well.
If your LS1010 is layer 2 only device then you will need another router
connected to LS1010 to establish connectivity at layer 3 with your 7505 over
a PVC that you configure on LS1010.
__________________________
#7247 (R&S, Security)
CyscoExpert Corp.
4433 W. Touhy Ave. Suite 410
Lincolnwood, IL 60712
Phone (847) 674-3392
Fax (847) 674-2625
----- Original Message -----
From: "Jason Cash" <cash2001@swbell.net>
To: <ccielab@groupstudy.com>
Sent: Tuesday, December 24, 2002 1:59 PM
Subject: ATM pvc config (w/ LS1010 7505)
> I am trying to set up an ATM pvc b/w an LS1010 and a 7505 (DS3 card).
> The problem I am running into is that I am able to config a subinterface
> on the 7505 but not on the LS1010. The following is the error on the
> LS:
>
> SW1.LS1010(config)#int a0/0/0.1
> ^
> % Invalid input detected at '^' marker.
>
> I am unfamiliar with setting up ATM pvcs, but have tried to duplicate
> the configs on the CCO. Also, there appear to be several vcs on the
> LS10101 that I don't see configured in the switch:
>
> SW1.LS1010#
> 6d22h: %SYS-5-CONFIG_I: Configured from console by consolesh atm vc
> Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status
> ATM0/0/0 0 5 PVC ATM2/0/0 0 43 QSAAL DOWN
> ATM0/0/0 0 16 PVC ATM2/0/0 0 35 ILMI DOWN
> ATM0/0/0 0 40 PVC NOT CONNECTED
> ATM0/0/1 0 5 PVC ATM2/0/0 0 44 QSAAL DOWN
> ATM0/0/1 0 16 PVC ATM2/0/0 0 36 ILMI DOWN
> ATM0/0/2 0 5 PVC ATM2/0/0 0 45 QSAAL DOWN
> ATM0/0/2 0 16 PVC ATM2/0/0 0 37 ILMI DOWN
> ATM0/0/3 0 5 PVC ATM2/0/0 0 46 QSAAL DOWN
> ATM0/0/3 0 16 PVC ATM2/0/0 0 38 ILMI DOWN
> ATM2/0/0 0 35 PVC ATM0/0/0 0 16 ILMI DOWN
> ATM2/0/0 0 36 PVC ATM0/0/1 0 16 ILMI DOWN
> ATM2/0/0 0 37 PVC ATM0/0/2 0 16 ILMI DOWN
> ATM2/0/0 0 38 PVC ATM0/0/3 0 16 ILMI DOWN
> ATM2/0/0 0 39 PVC ATM3/0/0 0 16 ILMI DOWN
> ATM2/0/0 0 40 PVC ATM3/0/1 0 16 ILMI DOWN
> ATM2/0/0 0 41 PVC ATM3/0/2 0 16 ILMI DOWN
> ATM2/0/0 0 42 PVC ATM3/0/3 0 16 ILMI DOWN
> ATM2/0/0 0 43 PVC ATM0/0/0 0 5 QSAAL DOWN
> ATM2/0/0 0 44 PVC ATM0/0/1 0 5 QSAAL DOWN
> ATM2/0/0 0 45 PVC ATM0/0/2 0 5 QSAAL DOWN
> ATM2/0/0 0 46 PVC ATM0/0/3 0 5 QSAAL DOWN
> ATM2/0/0 0 47 PVC ATM3/0/0 0 5 QSAAL DOWN
> Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status
> ATM2/0/0 0 48 PVC ATM3/0/1 0 5 QSAAL DOWN
> ATM2/0/0 0 49 PVC ATM3/0/2 0 5 QSAAL DOWN
> ATM2/0/0 0 50 PVC ATM3/0/3 0 5 QSAAL DOWN
> ATM3/0/0 0 5 PVC ATM2/0/0 0 47 QSAAL DOWN
> ATM3/0/0 0 16 PVC ATM2/0/0 0 39 ILMI DOWN
> ATM3/0/1 0 5 PVC ATM2/0/0 0 48 QSAAL DOWN
> ATM3/0/1 0 16 PVC ATM2/0/0 0 40 ILMI DOWN
> ATM3/0/2 0 5 PVC ATM2/0/0 0 49 QSAAL DOWN
> ATM3/0/2 0 16 PVC ATM2/0/0 0 41 ILMI DOWN
> ATM3/0/3 0 5 PVC ATM2/0/0 0 50 QSAAL DOWN
> ATM3/0/3 0 16 PVC ATM2/0/0 0 42 ILMI DOWN
>
> Below are the configs for the two devices. Is is possible to do what I
> am try to do? A sample of working config would be greatly appreciated!
>
> LS1010
>
> SW1.LS1010#sh run
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> no service pad
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname SW1.LS1010
> !
> !
> ip subnet-zero
> !
> atm qos default cbr max-cell-loss-ratio clp0 255
> atm qos default cbr max-cell-loss-ratio clp1plus0 255
> atm qos default vbr-rt max-cell-loss-ratio clp0 255
> atm qos default vbr-rt max-cell-loss-ratio clp1plus0 255
> atm qos default vbr-nrt max-cell-loss-ratio clp0 255
> atm qos default vbr-nrt max-cell-loss-ratio clp1plus0 255
> atm address 47.0091.8100.0000.0001.42e4.a101.0001.42e4.a101.00
> atm router pnni
> no aesa embedded-number left-justified
> node 1 level 56 lowest
> redistribute atm-static
> !
> !
> !
> interface ATM0/0/0
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> atm pvc 0 40
> !
> interface ATM0/0/1
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> !
> interface ATM0/0/2
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> !
> interface ATM0/0/3
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> !
> interface ATM2/0/0
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> atm maxvp-number 0
> !
> interface Ethernet2/0/0
> description oob_192.168.1.0
> ip address 192.168.1.1 255.255.255.0
> no ip directed-broadcast
> !
> interface ATM3/0/0
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> !
> interface ATM3/0/1
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> !
> interface ATM3/0/2
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> !
> interface ATM3/0/3
> no ip address
> no ip directed-broadcast
> logging event subif-link-status
> no atm ilmi-keepalive
> !
> ip classless
>
>
> 7505
>
> R4.7507#sh run
> Building configuration...
>
> Current configuration : 1822 bytes
> !
> version 12.1
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname R4.7507
> !
> ip subnet-zero
> no ip domain-lookup
> !
> no ip cef
> ip audit notify log
> ip audit po max-events 100
> !
> interface ATM0/0
> no ip address
> no atm ilmi-keepalive
> !
> interface ATM0/0.1 point-to-point
> ip address 172.16.10.1 255.255.255.0
> pvc 0/40
> protocol ip 172.16.10.1 broadcast
> protocol ip 172.16.10.2 broadcast
> !
> !
> !
> ip classless
> no ip http server
> !
> !
>
> The devices are connected via a DS3 crossover cable.
> .
.
This archive was generated by hypermail 2.1.4 : Fri Jan 17 2003 - 17:21:52 GMT-3