From: Matthew Poole (matthew.poole@blueyonder.co.uk)
Date: Tue Dec 17 2002 - 11:04:28 GMT-3
Tony - thanks for looking.
No routing at all, just what you see, no loopbacks etc
R5--------------------------R4
192.168.1.1 192.168.1.2
The counter doesn't get reset, it does count down from 120 seconds and then
clears down the line normally (n.b. paste taken from R4).
01:41:32: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from 325500
R5, c
all lasted 121 seconds
I have no problems when I go back to legacy dial string/map.
I have added your lines, everything still the same.
Interestingly when I add the dialer idle-timeout directly onto the dialer
interface it works, however I can't see why the map-class isn't working.
01:51:34: %ISDN-6-DISCONNECT: Interface BRI0/0:2 disconnected from 325600
R4, c
all lasted 21 seconds
Thanks,
----- Original Message -----
From: "Tony Kwok" <sykwok8@yahoo.com>
To: "Matthew Poole" <matthew.poole@blueyonder.co.uk>
Cc: <ccielab@groupstudy.com>
Sent: Tuesday, December 17, 2002 1:36 PM
Subject: Re: Dialer profile
> Dear Mathew,
>
> Are u running any dynamic routing? It may cause the
> idle timer to be triggered on every few seconds. U
> can try to change the access-list as follows to see
> whether the connection can be teared down
> automatically after u completed the ping.
>
> dialer-list 1 protocol ip list 100
> access-list 100 permit icmp any any
>
> Hope this help.
>
> Regards,
> Tony
>
> --- Matthew Poole <matthew.poole@blueyonder.co.uk>
> wrote:
> > I'm trying to configure a map-class dialer for my
> > dialer profile so that the
> > line clears down after 20 seconds:
> >
> > interface BRI0/0
> > no ip address
> > encapsulation ppp
> > dialer pool-member 1
> > isdn switch-type basic-net3
> > ppp authentication chap
> > !
> > !
> > interface Dialer1
> > ip address 192.168.1.1 255.255.255.0
> > encapsulation ppp
> > dialer pool 1
> > dialer remote-name R4
> > dialer string 325600 class profile
> > dialer-group 1
> > ppp authentication chap
> > !
> > !
> > map-class dialer profile
> > dialer idle-timeout 20
> > dialer fast-idle 15
> > dialer-list 1 protocol ip permit
> >
> > However when I do a ping and show isdn active, the
> > ping is successful but the
> > idle timout is still 120 Seconds? Output is below
> > with debug dialer.
> >
> > R5#ping 192.168.1.2
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 192.168.1.2,
> > timeout is 2 seconds:
> >
> > 00:47:09: BR0/0 DDR: rotor dialout [priority]
> > 00:47:09: BR0/0 DDR: Dialing cause ip
> > (s=192.168.1.1, d=192.168.1.2)
> > 00:47:09: BR0/0 DDR: Attempting to dial 325600
> > 00:47:47244640255: %LINK-3-UPDOWN: Interface
> > BRI0/0:2, changed state to up
> > 00:47:45123225436: BR0/0:2: interface must be fifo
> > queue, force fifo
> > 00:47:45123225252: %DIALER-6-BIND: Interface BR0/0:2
> > bound to profile
> > Di1.!!!!
> > Success rate is 80 percent (4/5), round-trip
> > min/avg/max = 28/31/32 ms
> > R5#
> > 00:47:10: BR0/0:2 DDR: dialer protocol up
> > R5#
> > 00:47:11: %LINEPROTO-5-UPDOWN: Line protocol on
> > Interface BRI0/0:2, changed
> > stat
> > e to up
> > R5#sh isdn active
> >
> --------------------------------------------------------------------------
--- > > --- > > ISDN ACTIVE CALLS > > > -------------------------------------------------------------------------- --- > > --- > > Call Calling Called Remote Seconds > > Seconds Seconds Charges > > Type Number Number Name Used > > Left Idle > > Units/Currency > > > -------------------------------------------------------------------------- --- > > --- > > Out 325600 R4 6 > > 114 5 0 > > > -------------------------------------------------------------------------- --- > > --- > > > > I've tried it by also placing dialer idle-timeout > > directly in the dialer but > > this had the same affect (i.e none!) > > > > Any ideas why it doesn't indicate 20 Seconds? > > Thanks. > > . > > > __________________________________________________________________ > > To unsubscribe from the CCIELAB list, send a message > > to > > majordomo@groupstudy.com with the body containing: > > unsubscribe ccielab > > > __________________________________________________ > Do you Yahoo!? > Yahoo! Mail Plus - Powerful. Affordable. Sign up now. > http://mailplus.yahoo.com .
This archive was generated by hypermail 2.1.4 : Fri Jan 17 2003 - 17:21:47 GMT-3