From: Sean Garrett (SGarrett@cnitech.com)
Date: Mon Dec 16 2002 - 16:27:33 GMT-3
If you aren't given a subnet to use on the tunnel itself,
what should you use there? Chop up one of the /24s given
at either end to use across the tunnel?
-----Original Message-----
From: Don [mailto:seadon@attbi.com]
Sent: Monday, December 16, 2002 11:01 AM
To: Kumar, Senthil; Abdallah Al-Suwailem
Cc: ccielab@groupstudy.com
Subject: Re: unicast-2-multicast
You can use a tunnel interface to get multicast across a link that only
supports unicast. Create a tunnel from one end to the other and then enable
multicast on the tunnel interfaces (and, of course, on the router interfaces
that do support multicast). This also works to load share multicast traffic
across multple links, something multicast cannot do by itself. PIM requires
all multicast interfaces to be in a unicast routing table and this can be a
problem with tunnels. If so, add a static multicast route (ip mroute
command) to fix this problem. See Doyle, Vol 2 page 596 for an example.
Don
----- Original Message -----
From: "Kumar, Senthil" <senthil.kumar@intechnology.co.uk>
To: "Abdallah Al-Suwailem" <aalsuwailem@myrealbox.com>; "Kumar, Senthil"
<senthil.kumar@intechnology.co.uk>
Cc: <ccielab@groupstudy.com>
Sent: Monday, December 16, 2002 8:21 AM
Subject: RE: unicast-2-multicast
> many thanks for your reply. but i was wondering i could could map even all
> unicasts to a host on a particular protocol and port number to convert it
> into a multicast to feed the multicast domain.. i've tried using
helper-map,
> configs look okay but couldnt figure out a method to do testing with it.
did
> permit udp any any broadcast-2-multicast-2broadcast. did forward protocol
> udp
> and enabled directed-broadcast..did a ping on the local segment x.x.x.255
> and 255.255.255.255 ..got reply from the local broadcast domain but the
> remote never replied..
>
>
>
> -----Original Message-----
> From: Abdallah Al-Suwailem [mailto:aalsuwailem@myrealbox.com]
> Sent: 16 December 2002 16:08
> To: Kumar, Senthil
> Cc: ccielab@groupstudy.com
> Subject: Re: unicast-2-multicast
>
>
>
> Hello
>
> check this command "r2(config-if)#ip multicast helper-map"
>
> r2(config-if)#ip multicast ?
> boundary Boundary for administratively scoped multicast addresses
> helper-map Broadcast to Multicast map OR Multicast to Broadcast map
> rate-limit Rate limit multicast data packets
> tagswitch Enable IP Multicast Tagswitching
> ttl-threshold TTL threshold for multicast packets
>
> Thanks
>
> Abdallah
>
> Kumar, Senthil wrote:
>
> >can nat convert all traffic on a local network, @ port xx.udp to
> mulitcast,
> >haven't got a traffic generator to test.
> >the idea is for the host on my brodcast lan to send data to multicast
> >machines hops away. my firsthop doesnt do mulitcast routing..
> >
> >any ideas, help very appreciated.
> >
> >Thanks, Senthil
> >
> >
> >
> >
> >________________________________________________________________________
> >This message has been checked for all known viruses by the
> >CitC Virus Scanning Service powered by SkyLabs. For further information
> visit
> >http://www.citc.it
> >
> >___
> >.
> ________________________________________________________________________
> This message has been checked for all known viruses by the
> CitC Virus Scanning Service powered by SkyLabs. For further information
> visit
> http://www.citc.it
>
> ___
>
> ________________________________________________________________________
> This message has been checked for all known viruses by the
> CitC Virus Scanning Service powered by SkyLabs. For further information
visit
> http://www.citc.it
>
> ___
> .
.
.
This archive was generated by hypermail 2.1.4 : Fri Jan 17 2003 - 17:21:46 GMT-3