From: McClure, Allen (Allen.McClure@Tricon-Yum.Com)
Date: Fri Nov 22 2002 - 12:42:17 GMT-3
I may be confused on the K numbers because I borrowed from other notes.
Point still stands, use an offset-list or tweak delay but not bandwidth.
Allen McClure
MCSE, CCNP, CCDP
YUM! Brands, Inc.
Sr. Network Analyst
NEW E-Mail - mailto:allen.mcclure@yum.com
972-338-7494
-----Original Message-----
From: McClure, Allen
Sent: Friday, November 22, 2002 9:40 AM
To: ccielab@groupstudy.com; 'adarshs@hclinfinet.net'
Subject: RE: How to change metric on EIGRP
I would personally also recommend you not mess with anything besides
K1,K2.
My recommendation is that you use one of two options based on your
scenario (in order of preference):
1. An eigrp offset-list
http://www.cisco.com/en/US/products/sw/iosswrel/ps1828/products_command_
summary_chapter09186a00800ef92d.html#xtocid16
2. Or set a higher delay on your interfaces to the VSAT network. I
don't like to set bandwidth to anything except the accurate bandwidth in
order to keep network management products and interface counters
straight.
Allen McClure
MCSE, CCNP, CCDP
YUM! Brands, Inc.
-----Original Message-----
From: Sam.MicroGate@usa.telekom.de [mailto:Sam.MicroGate@usa.telekom.de]
Sent: Friday, November 22, 2002 8:54 AM
To: lsong@dataphile.ca; Sam.MicroGate@usa.telekom.de;
adarshs@hclinfinet.net; ccielab@groupstudy.com
Subject: RE: How to change metric on EIGRP
Leo,
You just touched them in your formula. The minimum bandwidth and the
total delay are K1 and K2. How come you advice not to touch them while
you are using them your self?
Sam
-----Original Message-----
From: Leo Song [mailto:lsong@dataphile.ca]
Sent: Friday, November 22, 2002 9:52 AM
To: Sam.MicroGate@usa.telekom.de; adarshs@hclinfinet.net;
ccielab@groupstudy.com
Subject: RE: How to change metric on EIGRP
Metric (eigrp) = ( 10000000/minimum bandwidth + total delay ) x 256
Don't touch k1,k2 ,,, k5, you don't need to.
Leo
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Sam.MicroGate@usa.telekom.de
Sent: Friday, November 22, 2002 8:41 AM
To: adarshs@hclinfinet.net; ccielab@groupstudy.com
Subject: RE: How to change metric on EIGRP
Router(config-router)#metric weights tos k1 k2 k3 k4 k5
K1 is bandwidth
K2 is load
K3 is reliability
K4 forgot what is it
K5 is mtu
There is a formula to calculate the metric but I do not remember it. You
have to go the Doc CD or Jeff Doyle to find out how to calculate the
metric from this parameters.
Sam
-----Original Message-----
From: Adarsh Singh [mailto:adarshs@hclinfinet.net]
Sent: Friday, November 22, 2002 3:58 AM
To: ccielab@groupstudy.com
Subject: How to change metric on EIGRP
Hi All,
I have 2 eigrp routes in the router , one through leased line & second
thrrough VSAT.
It is HUB & SPOKE technology , could you tell me how do i set the
metric at the SPOKE or HUB so that first preffered path is leased line &
second one is VSAT. How do i change the metric ?
Rgds
Adarsh Singh
This communication is confidential and may be legally privileged. If you are not the intended recipient, (i) please do not read or disclose to others, (ii) please notify the sender by reply mail, and (iii) please delete this communication from your system. Failure to follow this process may be unlawful. Thank you for your cooperation.
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:23:09 GMT-3