From: MADMAN (dave@interprise.com)
Date: Mon Nov 04 2002 - 16:23:18 GMT-3
It's not secondary in config-sync mode, the keyword is "alt". Single
router mode has no special commands other than
!
redundancy
high-availability
single-router-mode
!
It runs in a master/slave relationship similiar to dual RSP's in a
7500:
MSFC_15#sh redun
Designated Router: 1 Non-designated Router: 2
Redundancy Status: designated
Config Sync AdminStatus : enabled
Config Sync RuntimeStatus: enabled
Single Router Mode AdminStatus : enabled
Single Router Mode RuntimeStatus: enabled
Dave
"Larson, Chris" wrote:
>
> That is what I said. Eiterh configure it using the high availability config
> synch
> ie. (this IS SRM configuration)
>
> interface vlan 2
> ip add x.x.x.x x.x.x.x secondary ip add x.x.x.x x.x.x.x
> standby ip x.x.x.x secondary standby ip x.x.x.x x.x.x.x
>
> interface flexwan(ATM0)
> ip add x.x.x.x x.x.x.x secondary ip add x.x.x.x x.x.x.x
>
> Or you configure the active MSFC with flexwan. Failover, configure the
> secondary MSFC with the flexwan. Then fail back.
>
> > -----Original Message-----
> > From: Joseph Ezerski [SMTP:jezerski@broadcom.com]
> > Sent: Monday, November 04, 2002 12:20 PM
> > To: 'Chris'; 'Tim O'Brien'; cisco@groupstudy.com; ccielab@groupstudy.com
> > Subject: RE: 6509 w/2 SUP2/MSFC2 and FlexWAN
> >
> > I think what Chris wrote is not quite the full story. I am currently
> > using
> > a SUP1A and MSFC1 with a Flexwan card. We are also using
> > single-router-mode, which is the Cisco recommended way of implementing
> > redundancy in the Cat6509. With SRM, you can configure everything you
> > need
> > on the DR and, anytime you do a write, all configs will transfer to the
> > NDR. In the event of a failure, the Flexwan will be recognized by the
> > second MSFC when it assumes the DR duties.
> >
> > HTH
> >
> > -Joe
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > Chris
> > Sent: Sunday, November 03, 2002 1:56 PM
> > To: Tim O'Brien; cisco@groupstudy.com; ccielab@groupstudy.com
> > Subject: Re: 6509 w/2 SUP2/MSFC2 and FlexWAN
> >
> >
> > You either have to use the high availability config synch config options.
> > ie.
> >
> > Interface lvan 2
> > ip add x.x.x.x x.x.x.x standby ip add x.x.x.x x.x.x.x
> >
> > or you have to config everything on the active including the Flexwan, fail
> > it over and config everything on the standby including Flexwan then fail
> > it
> > back.
> >
> >
> >
> > ----- Original Message -----
> > From: "Tim O'Brien" <tobrien@cinci.rr.com>
> > To: <cisco@groupstudy.com>; <ccielab@groupstudy.com>
> > Sent: Sunday, November 03, 2002 3:17 PM
> > Subject: OT: 6509 w/2 SUP2/MSFC2 and FlexWAN
> >
> >
> > > Hello,
> > >
> > > I am working on a high availability solution for a single 6509. The
> > > customer currently has a 6509 with dual SUP 2's and dual MSFC2/PFC2's.
> > > This box also has a FlexWAN module and I am having some difficulty
> > > locating any useful information on Cisco's new site about setting this
> > > up with some high availability or redundancy. When I configure the
> > > MSFC's like normal with HSRP on all of the VLAN interfaces only the MSFC
> > > in the active SUP can see the FlexWAN module and serial ports. They do
> > > not even show up on the second MSFC. Is there a "Ciscoized" way to set
> > > this up?
> > >
> > > Thanks for any help!
> > >
> > > Tim
-- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications 612-664-3367"You don't make the poor richer by making the rich poorer." --Winston Churchill
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:22:52 GMT-3