From: Larson, Chris (CLarson@usaid.gov)
Date: Mon Nov 04 2002 - 14:58:17 GMT-3
That is what I said. Eiterh configure it using the high availability config
synch
ie. (this IS SRM configuration)
interface vlan 2
ip add x.x.x.x x.x.x.x secondary ip add x.x.x.x x.x.x.x
standby ip x.x.x.x secondary standby ip x.x.x.x x.x.x.x
interface flexwan(ATM0)
ip add x.x.x.x x.x.x.x secondary ip add x.x.x.x x.x.x.x
Or you configure the active MSFC with flexwan. Failover, configure the
secondary MSFC with the flexwan. Then fail back.
> -----Original Message-----
> From: Joseph Ezerski [SMTP:jezerski@broadcom.com]
> Sent: Monday, November 04, 2002 12:20 PM
> To: 'Chris'; 'Tim O'Brien'; cisco@groupstudy.com; ccielab@groupstudy.com
> Subject: RE: 6509 w/2 SUP2/MSFC2 and FlexWAN
>
> I think what Chris wrote is not quite the full story. I am currently
> using
> a SUP1A and MSFC1 with a Flexwan card. We are also using
> single-router-mode, which is the Cisco recommended way of implementing
> redundancy in the Cat6509. With SRM, you can configure everything you
> need
> on the DR and, anytime you do a write, all configs will transfer to the
> NDR. In the event of a failure, the Flexwan will be recognized by the
> second MSFC when it assumes the DR duties.
>
> HTH
>
> -Joe
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Chris
> Sent: Sunday, November 03, 2002 1:56 PM
> To: Tim O'Brien; cisco@groupstudy.com; ccielab@groupstudy.com
> Subject: Re: 6509 w/2 SUP2/MSFC2 and FlexWAN
>
>
> You either have to use the high availability config synch config options.
> ie.
>
> Interface lvan 2
> ip add x.x.x.x x.x.x.x standby ip add x.x.x.x x.x.x.x
>
> or you have to config everything on the active including the Flexwan, fail
> it over and config everything on the standby including Flexwan then fail
> it
> back.
>
>
>
> ----- Original Message -----
> From: "Tim O'Brien" <tobrien@cinci.rr.com>
> To: <cisco@groupstudy.com>; <ccielab@groupstudy.com>
> Sent: Sunday, November 03, 2002 3:17 PM
> Subject: OT: 6509 w/2 SUP2/MSFC2 and FlexWAN
>
>
> > Hello,
> >
> > I am working on a high availability solution for a single 6509. The
> > customer currently has a 6509 with dual SUP 2's and dual MSFC2/PFC2's.
> > This box also has a FlexWAN module and I am having some difficulty
> > locating any useful information on Cisco's new site about setting this
> > up with some high availability or redundancy. When I configure the
> > MSFC's like normal with HSRP on all of the VLAN interfaces only the MSFC
> > in the active SUP can see the FlexWAN module and serial ports. They do
> > not even show up on the second MSFC. Is there a "Ciscoized" way to set
> > this up?
> >
> > Thanks for any help!
> >
> > Tim
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:22:52 GMT-3