From: Senthil Kumar (senthil.kumar@intechnology.co.uk)
Date: Mon Nov 04 2002 - 13:42:12 GMT-3
be aware of extended vlan support, which is why you could configure vlans in
ios. also when you have configs in vlan database and in ios.. there are some
complications addressed with domain name choosen, i'd recommend using vlan
database if there is no special need like creating vlan 4095.
-----Original Message-----
From: Paglia, John (USPC.PCT.Hopewell) [mailto:JPaglia@NA2.US.ML.com]
Sent: 23 October 2002 17:08
To: 'LoizosCisco'; 'Cameron, John'; 'Donny MATEO'; Alec
Cc: Ccielab@Groupstudy.Com
Subject: RE: vtp question
Absolutely, but mainly when you refer to specific naming. Using the method
Mr. Cameron detailed below, a VLAN #37 will be created with the name
VLAN0037. Not a very descriptive name at all. That's why one would use the
global config or Vlan Database...so they can type in:
vlan 37 name Marketing_Vlan (lame example). Now ya know right away what vlan
37 is being used for!
John
> -----Original Message-----
> From: LoizosCisco [SMTP:david_steven2001@yahoo.com]
> Sent: Wednesday, October 23, 2002 11:35 AM
> To: Paglia, John (USPC.PCT.Hopewell); 'Cameron, John'; 'Donny MATEO';
> Alec
> Cc: Ccielab@Groupstudy.Com
> Subject: RE: vtp question
>
> If you are asked to give specific names/numbers to
> vlans then you have to create them first right?
>
>
> --- "Paglia, John (USPC.PCT.Hopewell)"
> <JPaglia@NA2.US.ML.com> wrote:
> > No, this will indeed create the vlan. In fact, you
> > don't need to access the
> > VLAN Database at all to make VLAN's...VLAN configs
> > can also be done in
> > global config mode. Doing it the way you described
> > will create a vlan with a
> > generic name. Check out the PDF at this link on
> > basic 3550
> > configuration..it'll explain it well.
> >
> > http://www.netmasterclass.net/site/lib.php
> >
> > John
> >
> >
> >
> > > -----Original Message-----
> > > From: Cameron, John [SMTP:johcamer@cisco.com]
> > > Sent: Wednesday, October 23, 2002 9:35 AM
> > > To: 'Donny MATEO'; Alec
> > > Cc: Ccielab@Groupstudy.Com
> > > Subject: RE: vtp question
> > >
> > > Team,
> > >
> > > When configuring and assigning a port to a vlan I
> > usually do the
> > > following:
> > >
> > > s1#c
> > > Enter configuration commands, one per line. End
> > with CNTL/Z.
> > > s1(config)#int f0/24
> > > s1(config-if)#switch mode access
> > > s1(config-if)#switch access vlan 37
> > > % Access VLAN does not exist. Creating vlan 37
> > >
> > > I never need to go into the vlan dbase to create
> > the vlan first. This has
> > > always worked for me. Does anyone know if this
> > approach creates any
> > > undesirable side
> > > effects.
> > >
> > > Thanks,
> > > JDC
> > >
> > >
> > > -----Original Message-----
> > > From: Donny MATEO
> > [mailto:donny.mateo@sg.ca-indosuez.com]
> > > Sent: Tuesday, October 22, 2002 9:48 PM
> > > To: Alec
> > > Cc: Ccielab@Groupstudy.Com; nobody@groupstudy.com
> > > Subject: Re: vtp question
> > >
> > >
> > > Alec,
> > >
> > > creating vlan and assigning vlan to a port is two
> > different thing.
> > > when you create a vlan you do
> > > vlan database
> > > vlan 10 name test bla bla bla
> > > exit
> > >
> > > when you assign a vlan to a port you do
> > > conf t
> > > int fa0/1
> > > switchport access vlan 10
> > > end
> > >
> > >
> > > what it means by not able to create a vlan is the
> > first one. Only the VTP
> > > server can create vlan and
> > > the information is flooded to all vtp client. Now
> > on the client just need
> > > to
> > > assign the vlan to the
> > > interface.
> > > Hope that's clear enough for you.
> > >
> > > Donny
> > >
> > >
> > >
> > >
> > > "Alec"
> > >
> > > <clapun@graduate. To:
> > > "Ccielab@Groupstudy.Com" <ccielab@groupstudy.com>
> > >
> > > hku.hk> cc:
> > >
> > > Sent by:
> > Subject: vtp question
> > >
> > > nobody@groupstudy
> > >
> > > .com
> > >
> > >
> > >
> > >
> > >
> > > 23-10-2002 00:58
> > >
> > > Please respond to
> > >
> > > "Alec"
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > Hi group,
> > >
> > > I'm a newcomer in groupstudy and confused by the
> > VTP client mode. From
> > > cisco
> > > documentation, a switch running VTP client mode
> > can not create VLAN. So
> > > how
> > > can the VTP server switch instructs the client to
> > add a VLAN to its
> > > customer-facing port, say adding VLAN 500 to 12/1
> > ? It seems there is no
> > > field for slot/port in the VTP messages. Please
> > correct me if my
> > > interpretation was wrong. Thanks.
> > >
> > > regards,
> > > alec
>
>
> __________________________________________________
> Do you Yahoo!?
> Y! Web Hosting - Let the expert host your web site
> http://webhosting.yahoo.com/
This archive was generated by hypermail 2.1.4 : Tue Dec 03 2002 - 07:22:52 GMT-3