From: Brad Bonham (bbonham@cisco.com)
Date: Wed Oct 23 2002 - 16:23:12 GMT-3
A good link on demand circuit
http://www.cisco.com/warp/public/104/dcprob.html
----- Original Message -----
From: "Larson, Chris" <CLarson@usaid.gov>
To: "'Paglia, John (USPC.PCT.Hopewell)'" <JPaglia@NA2.US.ML.com>;
"'enginedrive2002'" <enginedrive2002@yahoo.ca>; <ccielab@groupstudy.com>
Sent: Wednesday, October 23, 2002 1:00 PM
Subject: RE: DDR question.
> If periodic hello's and lsa's are suppressed so they do not flood the
demand
> circuit. AND
>
> "only periodic hellos and refreshes of LSA's once the call is made"
>
> Then why is the 101 list needed? It says that hello's and lsa's will not
be
> sent until after the call is made? Why do you need to supress them twice?
>
>
>
> > -----Original Message-----
> > From: Paglia, John (USPC.PCT.Hopewell) [SMTP:JPaglia@NA2.US.ML.com]
> > Sent: Wednesday, October 23, 2002 2:08 PM
> > To: 'enginedrive2002'; ccielab@groupstudy.com
> > Subject: RE: DDR question.
> >
> > The definition of 'demand-circuit' as per the 12.1 cmd. ref.:
> > Periodic hellos are suppressed and periodic refreshes of LSAs do not
flood
> > the demand circuit. It allows the underlying datalink layer to be closed
> > when the topology is stable.
> > ...only periodic hellos and refreshes of LSA's once the call is made.
> > Thus,
> > you put the 'deny ospf any any' cmd. in to keep hello's from acting as
the
> > 'interesting traffic' that can initialize a link. Once non-ospf traffic
> > brings up the link, demand-circuit kicks in.
> >
> > Here's the link:
> >
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/ip
> > _r
> > /iprprt2/1rdospf.htm#xtocid19
> > Watch the wrap!!!
> >
> > John
> >
> > > -----Original Message-----
> > > From: enginedrive2002 [SMTP:enginedrive2002@yahoo.ca]
> > > Sent: Wednesday, October 23, 2002 12:51 PM
> > > To: ccielab@groupstudy.com
> > > Subject: DDR question.
> > >
> > > Would someone read the doc link below, and answer a few questions:
> > > http://www.cisco.com/warp/public/129/config-bri-map.html
> > >
> > > 1. On router maui-soho-01, "ip ospf demand-circuit" is configured
under
> > > BRI
> > > interface, why in the example, access-list 101 still need to have
"deny
> > > ospf
> > > any any"? I have never test OSPF demand-circuit at before, but I
"guess"
> > > with
> > > the "ip ospf demand-circuit" command, it will already suppress the
hello
> > > packets. Would someone confirm this?
> > >
> > > 2. On router maui-nas-05, under BRI interface, the example doesn't
> > > configure
> > > any number to dial, which mean it could only answer the call. But why
in
> > > the
> > > example, it has "dialer-group", "dialer-list" command to define
> > > interesting
> > > traffic? Just to reset the idle-timer while the BRI link is up? Any
> > other
> > > purpose here?
> > >
> > > Thank you!
> > >
> > >
> > > Regards,
> > >
> > >
> > > E.D.
This archive was generated by hypermail 2.1.4 : Tue Nov 05 2002 - 08:35:54 GMT-3