From: Brian McGahan (brian@cyscoexpert.com)
Date: Thu Oct 17 2002 - 09:45:17 GMT-3
"(and so i delete the ILMI PVC, because i don't need it to learn the
prefix)"
That's your problem. When running SVCs, you always need the qsaal and
ilmi vcs.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/
wan_c/wcdatm.htm#36179
HTH
Brian McGahan, CCIE #8593
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
Of
> Joe A
> Sent: Wednesday, October 16, 2002 9:51 PM
> To: 'Benny Chong'; ccielab@groupstudy.com
> Subject: RE: ATM RFC 2684 svc don't work using full nsap address
>
> I tried for a long time to figure this one out and finally just gave
up,
> assuming it must be a code version problem; I could not find a bug
> listed either. I even got it to a point were it DID work, but not
after
> rebooting the routers.
>
> Joe
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
Of
> Benny Chong
> Sent: Wednesday, October 16, 2002 8:01 PM
> To: ccielab@groupstudy.com
> Subject: ATM RFC 2684 svc don't work using full nsap address
>
>
> Hi,
>
> I just tested the Solie's book RFC 2684 SVC implementation. My
problem
> is,
> if I use the esi-address and setup the ILMI pvc, then everything is
> fine,
> but if I use the full nsap-address (and so i delete the ILMI PVC,
> because i
> don't need it to learn the prefix), it won't work. Does anyone have
> any
> idea why? The topology is simple, just 2 router with ATM interface
> connect
> to a ATM switch in between, trying to ping each other.
>
> Below are the working config using esi-address and ilmi PVC, and the
> non-working config is just removed the ilmi pvc and esi-address
command
> line
> in the bracket and use full nsap-address as shown below. Thanks very
> much!
>
> Router 1 config:
>
> interface ATM2/0
> no ip address
> (atm pvc 2 0 16 ilmi)
> atm pvc 5 0 5 qsaal
> no atm ilmi-keepalive
> !
> interface ATM2/0.1 multipoint
> ip address 100.100.100.1 255.255.255.0
> map-group 1
> (atm esi-address 131313131313.00) -> atm nsap-address
> 47.009181000000123412341234.131313131313.00
> ! (use
> this
> nsap address to replace the esi address, same below)
> !
> map-list 1
> ip 100.100.100.2 atm-nsap 47.009181000000123412341234.141414141414.00
> broadcas
>
>
>
> Router 2 config:
>
> interface ATM2/0
> no ip address
> (atm pvc 2 0 16 ilmi)
> atm pvc 5 0 5 qsaal
> no atm ilmi-keepalive
> !
> interface ATM2/0.1 multipoint
> ip address 100.100.100.2 255.255.255.0
> map-group 1
> (atm esi-address 141414141414.00) -> atm nsap-address
> 47.009181000000123412341234.141414141414.00
> !
> !
> map-list 1
> ip 100.100.100.1 atm-nsap 47.009181000000123412341234.131313131313.00
> broadcas
>
> _________________________________________________________________
> Broadband? Dial-up? Get reliable MSN Internet Access.
> http://resourcecenter.msn.com/access/plans/default.asp
This archive was generated by hypermail 2.1.4 : Tue Nov 05 2002 - 08:35:49 GMT-3