From: MADMAN (dave@interprise.com)
Date: Fri Oct 11 2002 - 12:40:02 GMT-3
FWIW I tried it also, same results and I'm running the latest IOS.
Dave
_mkadlc _ wrote:
>
> Hi guys,I am playing around with a 3550-24-emi and trying to make the
> routing ports work with the no keep command. I am not able to make it
> function as it would on router (2514). The short of the story is that I
> do the following1. issue the Ip routing command.2. go into the
> interface and issue the no switchport command3. type in the ip address I
> want4. do the no keep. (trying to bring up the interface without needing
> anything attached to it) I cant seem to get it to workbelow is a copy of
> what I did on int fas 0/2 to try to make the no keep work.yang#sh run
> ...
> !
> ip routing
> !
> interface Fastethernet0/2
> no ip address
> ....yang#sh ip int bri
> Fastethernet0/2 unassigned YES unset down down
> ..Yang#config t
> yang(config)#int fas 0/2
> yangconfig-if)#no shut
> 00:06:17: %lineproto-5-updown: line protocol on inteface fastethernet
> 0/2, changed state to down
> yang(config-if)#no switchport
> yang(config-if)#ip address 10.0.0.1 255.255.255.0
> yang(config-if)#no keep
> 00:12:24: %lineproto-5-updown: line protocol on inteface fastethernet
> 0/2, changed state to down
> yang(config-if)#end
> yang#sh int fas 0/2
> fastethernet0/2 is down, line protocol is down
> ...
> ...
> Keepalive not set Here is the config for int fas 0/1 which is connected
> to a 2514 yang#sh run
> ...
> !
> ip routing
> ...
> !
> interface Fastethernet0/1
> no ip address
> interface fasterethernet0/2
> no switchport
> ip address 10.0.0.1 255.255.255.0
> no keepalive
> ....
> yang#sh ip int bri
> fastethernet0/1 unassigned YES unset up up
> Fastethernet0/2 10.0.0.1 YES manual down down
> ...Yang#config t
> yang(config)#int fas 0/2
> yang(config-if)#no switchport
> 00:26:21: %lineproto-5-updown: line protocol on inteface fastethernet
> 0/2, changed state to down
> yang(config-if)#
> 00:26:22: %link-3-updown: interface fasterthernet 0/1, changed state to
> down
> yang(config-if)#
> 00:26:25: %lineproto-5-updown: line protocol on inteface fastethernet
> 0/2, changed state to up
> yang(config-if)#ip address 10.0.0.1 255.255.255.0
> yang(config-if)#end
> yang#sh int fas 0/1
> fastethernet0/1 is up, line protocol is up
> ....
> yang#sh ip int bri
> ....
> fastethernet0/1 172.27.200.1 YES manual up up
> Fastethernet0/2 10.0.0.1 YES manual down down
> ...
> Thanks for your help and looking at the my issue.Matthew Anglin
>
> ------------------------------------------------------------------------
>
> Join the worlds largest e-mail service with MSN Hotmail. Click Here
-- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications 612-664-3367"You don't make the poor richer by making the rich poorer." --Winston Churchill
This archive was generated by hypermail 2.1.4 : Tue Nov 05 2002 - 08:35:45 GMT-3