From: esther (esther1616@hanmail.net)
Date: Tue Oct 08 2002 - 23:31:27 GMT-3
Thanks all your replies.
Yes, I got it after making 4 sub-interfaces, each has different encap
type.
And the CDP will not be answer, I tested.
Thanks all again,
Esther.
---------[ 9^@: 8^@O 3;?k ]----------
> Title : RE: how to detect hidden ipx number
> Date : Wed, 9 Oct 2002 09:01:50 +1300
> From : Justin Cook
> To : "'Larson, Chris'" , "'C. Warren'",Justin Cook ,"'esther'" ,
ccielab@groupstudy.com
>
> That is why you connect to the switch, and do it from there as I
mentioned
> there are some blocks but ways around them
>
>
> --
> Justin Cook
> Systems Consultant
> MCSE +I, CCDP, CCNP(Security, Voice)
> Computerland Wellington
>
> DDI: 04 4606000
> Cellphone: 021 2408689
> Email: Justin.Cook@Computerland.co.nz > >
>
> CAUTION: This e-mail message and accompanying data may contain
Information
> that is confidential and subject to privilege. If you are not the
intended
> recipient, you are notified that any use, dissemination, distribution
or
> copying of this message or data is prohibited. If you have received
this
> e-mail in error, please notify me immediately and delete all material
> pertaining to this e-mail. Thank you.
>
> -----Original Message-----
> From: Larson, Chris [mailto:CLarson@usaid.gov]
> Sent: Wednesday, 9 October 2002 12:57 a.m.
> To: 'C. Warren'; 'Justin Cook'; 'esther'; ccielab@groupstudy.com
> Subject: RE: how to detect hidden ipx number
>
> I think what you need to do is to build subinterfaces with a different
IPX
> encapsulation on each one. Give each on an IPX network number and place
them
> all in rip. Debug, the router should complain.
>
> No, CDP will not work. If you are connectwed to a switch all CDP is
gonna
> give you is the swich info, not neighboring routers.
>
> -----Original Message-----
> From: C. Warren [SMTP:chwarren@cox.net]
> Sent: Monday, October 07, 2002 7:40 PM
> To: 'Justin Cook'; 'esther'; ccielab@groupstudy.com
> Subject: RE: how to detect hidden ipx number
> What if cdp isn't enabled?
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com
> ] On
> > Behalf Of Justin Cook
> > Sent: Monday, October 07, 2002 4:17 PM
> > To: 'esther'; ccielab@groupstudy.com
> > Subject: RE: how to detect hidden ipx number
> >
> >
> > Wouldn't cdp give you this information as well?
> >
> >
> > Did a test a managed to get the ipx network number of the
> > directly attached device
> >
> > Warrented there are a few blocks but it seems to work ok
> >
> > --
> > Justin Cook
> >
> >
> > -----Original Message-----
> > From: esther [mailto:esther1616@hanmail.net
> ]
> > Sent: Saturday, 5 October 2002 8:44 p.m.
> > To: ccielab@groupstudy.com
> > Subject: how to detect hidden ipx number
> >
> > Hi all,
> >
> > To detect a hidden ipx number, I did the following step.
> >
> > R1 --- (ipx ?)----- (Ethernet) -----(ipx 200) -- R2
> >
> > R1#
> > R1#debug ipx packet
> > IPX packet debugging is on
> > R1#
> > R1#conf t
> > Enter configuration commands, one per line. End with CNTL/Z.
> > R1(config)#int e0 R1(config-if)#ipx network 10 .... assigned
> > a discretionary ipx no. 10 R1(config-if)# R1(config-if)#
> >
> > No debugging messages are appeared, I expected mismatch ipx
> > network number. Anyone help me how to detect the hidden ipx
> > network number?
> >
> > Thanks in advance,
> >
> > Esther.
> > [TABLE NOT SHOWN]
> >
> > [TABLE NOT SHOWN][TABLE NOT SHOWN][IMAGE]
>
>
[TABLE NOT SHOWN]
[TABLE NOT SHOWN][TABLE NOT SHOWN][IMAGE]
This archive was generated by hypermail 2.1.4 : Tue Nov 05 2002 - 08:35:43 GMT-3