From: Erick B. (erickbe@yahoo.com)
Date: Mon Oct 07 2002 - 02:51:52 GMT-3
Adarsh,
Yes, Queueing (CBWFQ, etc) needs to be done on all
routers between the source and destination in the
outbound direction. Serial interfaces are fine but you
can also do ethernet if you want. All forms of
queueing are local to the router.
"When i talk between the voice boxes it uses exactlt
30000 series of udp ports & Ip ports"
So your access-list permitting UDP Ports >20000 covers
this range of 30000 ports, and are they all UDP?
Do you have any documentation on the ports and
protocols (might be UDP and TCP) used by the Ericsson
voip box?
--- Adarsh Singh <adarshs@hclinfinet.net> wrote:
> Hi Eric
>
> I would redescribe the setup .
>
> VOIP BOX(erricson)----HUB-----Router
>
(1603)-----backtoback(2601)--------backtoback(1603)----HUB---VOIPBOX(erricso
> n).
>
> First step i took was to debug ip packet detail :
> When i talk between the
> voice boxes it uses exactlt 30000 series of udp
> ports & Ip ports.
> Now this is a test setup , so there is no other
> traffic coming on the above
> described network.
>
> The CBWFQ is configured on the serial interface
> connected to 2601 router .
> The classification of the pakets is done by using
> the access-list .
> The ip address of the VOIP boxes are 10.66.6.36/29
> & 10.66.6.124/29.
>
> The output of the show access-list is s follows :
> Extended IP access list 102
> permit udp host 10.66.6.124 gt 20000 host
> 10.66.6.36 gt 20000 (20315
> matches)
>
> Now my objective is that whenever i am doign a voice
> conversation , a
> guranteed bandwidth is reserved for the voice , say
> 30 Kbps , actually the
> codes used in the voip boxes is G 729 , which
> utilizes 12 Kbps , which i
> have tested by talking between two voip boxes with
> no other traffic .
>
> Other than the above setup two pc are connected to
> the network diagram to
> generate the ftp data between the two , so that the
> load can be put on the
> serail link .
> Once that happens the voice starts breaking & cant
> hear the other person
> clearly.
> Now i am wondering if i am doing the things properly
> , i.e is theCBWFQ needs
> to be done on the serial port of the end routers
> only or also in the
> internediarly routers, do i need to put CBWFQ on the
> ethernet ports of both
> the 1603 routers.
>
> I have not been able to found any doc on CBWFQ which
> states that the CBWFQ
> needs to be done on the intermediary routers too.
> Pls suggest.
>
>
> The config of the routers are as mentioned in my
> previous mail.
>
> Thanks
> Adarsh
>
> ----- Original Message -----
> From: "Erick B." <erickbe@yahoo.com>
> To: "Adarsh Singh" <adarshs@hclinfinet.net>; "CCIE
> Group Study (E-mail)"
> <ccielab@groupstudy.com>
> Sent: Monday, October 07, 2002 10:40 AM
> Subject: Re: CBWFQ not working on 1603 for
> VOICE--HELP NEEDED URGENTLY
>
>
> > Adarsh,
> >
> > What is your current policy, class, and
> access-lists
> > like? Please post them.
> >
> > If they are still like below, only matching udp
> > traffic above port 20000 doesn't cover all voice
> > traffic. The 2 hosts 10.66.6.124 and 10.66.6.36
> are
> > the only voip enabled devices right (the router
> with
> > the policys is just routing IP and not doing
> voice?)
> >
> > Are these 2 hosts Cisco VoIP devices, or something
> > else that may possibly be using other port ranges?
> You
> > could take the other gentlemens suggestion and
> mark
> > anything from these sources with precedence of 5
> if
> > all they are doing is voice.
> >
> > Erick
> >
> > --- Adarsh Singh <adarshs@hclinfinet.net> wrote:
> > > Erik either marking the packets with Ip
> precedence 5
> > > or matching the
> > > packets with access-list shd work , but in my
> case
> > > when i choke the 64 Kbps
> > > link between the two routers doing the ftp ,
> there
> > > is no bandwidth
> > > reservation of 30 Kbps out of 64 Kbps on the
> serial
> > > interface taking place
> > > , so when the link is completely loaded with ftp
> > > traffic i.e upto 62 to 62
> > > Kbps, my voice traffic suffers , ideally it
> should
> > > reserve a bandwidth of
> > > 30 Kbps out of 64 Kbps, but that is not
> happening ,
> > > any further idea how do
> > > i go about it .
> > > Thanks
> > > Adarsh
> > > ----- Original Message -----
> > > From: "Erick B." <erickbe@yahoo.com>
> > > To: "Adarsh Singh" <adarshs@hclinfinet.net>;
> "CCIE
> > > Group Study (E-mail)"
> > > <ccielab@groupstudy.com>
> > > Sent: Sunday, October 06, 2002 3:44 AM
> > > Subject: Re: CBWFQ not working on 1603 for
> > > VOICE--HELP NEEDED URGENTLY
> > >
> > >
> > > > Adarsh,
> > > >
> > > > It depends on how granular you want to get.
> You
> > > could
> > > > mark inbound packets from your voice-enabled
> > > devices
> > > > with ip precedence of 5, etc then on the class
> > > just
> > > > match ip precedence 5.
> > > >
> > > > In the sample I posted, theres a chance
> non-voice
> > > > traffic that falls in the same port ranges as
> > > voice
> > > > will be prioritized as voice traffic.
> > > >
> > > > --- Adarsh Singh <adarshs@hclinfinet.net>
> wrote:
> > > > > Hi
> > > > >
> > > > > Do i need to mark packets on the ethernet
> port
> > > first
> > > > > , by using the
> > > > > acces-list as you have mentioned
> > > > >
> > > > > access-list 100 permit ip any any precedence
> > > > > critical
> > > > > > access-list 100 permit udp any any range
> 16384
> > > > > 32767
> > > > > > access-list 100 permit ip any any dscp ef
> > > > > > access-list 100 permit udp any range 16384
> > > 32767
> > > > > any
> > > > >
> > > > > But in my scenario i would be marking the
> > > packets
> > > > > only between the first
> > > > > voip box & the second one , i.e 10.66.6.126
> &
> > > > > 10.66.6.35.
> > > > > How do i apply the marking of the packets on
> the
> > > > > ethernet, could you tell
> > > > > me how do that part , do i need to apply
> this
> > > > > marking on both ends of the
> > > > > router at the ethernet port.
> > > > >
> > > > > This is test setup so i have no other
> traffic
> > > > > between the two routers .
> > > > > Inspite of the fact thet packets are
> matching
> > > the
> > > > > qos is not working, the
> > > > > voice is still breaking a lot .
> > > > > the current config for the serial port for
> both
> > > > > routers are as follows :
> > > > >
> > > > >
> > > > > router 1
> > > > >
> > > > > class-map voice
> > > > > match access-group 102
> > > > > !
> > > > > !
> > > > > policy-map test
> > > > > class voice
> > > > > priority 30
> > > > > class class-default
> > > > > fair-queue
> > > > > policy-map tes
> > > > >
> > > > >
> > > > > interface Serial0
> > > > > description connected to Infinet 64K leased
> > > line
> > > > > for vpn
> > > > > bandwidth 64
> > > > > ip address 10.66.2.122 255.255.255.252
> > > > > no ip route-cache
> > > > > no ip mroute-cache
> > > > > load-interval 30
> > > > > max-reserved-bandwidth 90
> > > > > service-policy output test
> > > > > clockrate 64000
> > > > >
> > > > > access-list 102 permit udp host 10.66.6.124
> gt
> > > 20000
> > > > > host 10.66.6.36 gt
> > > > > 20000
> > > > >
> > > > >
> > > > > router 2
> > > > >
> > > > >
> > > > > class-map voice
> > > > > match access-group 102
> > > > > !
> > > > > !
> > > > > policy-map test
> > > > > class voice
> > > > > priority 30
> > > > > class class-default
> > > > > fair-queue
> > > > > !
> > > > > interface Serial0
> > > > > description connected to Internet
> > > > > bandwidth 64
> > > > > ip address 10.66.2.98 255.255.255.252
> > > > > no ip route-cache
> > > > > no ip mroute-cache
> > > > > load-interval 30
> > > > > max-reserved-bandwidth 90
> > > > > service-policy output test
> > > > > !
> > > > > access-list 102 permit udp host 10.66.6.36
> gt
> > > 20000
> > > > > host 10.66.6.124 gt
> > > > > 20000
> > > > >
> > > > > Kindly let me know if you have any ideas.
> > > > >
> > > > > Rgds
> > > > > Adarsh
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > Adarsh
> > > > > ----- Original Message -----
> > > > > From: "Erick B." <erickbe@yahoo.com>
> > > > > To: "Adarsh Singh" <adarshs@hclinfinet.net>;
> > > "CCIE
> > > > > Group Study (E-mail)"
> > > > > <ccielab@groupstudy.com>
> > > > > Sent: Friday, October 04, 2002 9:35 PM
> > > > > Subject: Re: CBWFQ not working on 1603 for
> > > > > VOICE--HELP NEEDED URGENTLY
> > > > >
> > > > >
> > > > > > Try making your classes and ACLs more
> > > detailed.
> > > > > >
> > > > > > class-map match-all voip_traffic
> > > > > > match access-group 100
> > > > > > class-map match-all voip_control
> > > > > > match access-group 101
> > > > > >
> > > > > > policy-map llq_256_voice_3calls
> > > > > > class voip_traffic
> > > > > > priority 134
> > > > > > class voip_control
> > > > > > bandwidth 8
> > > > > > class class-default
> > > > > > fair-queue
> > > > > >
> > > > > > access-list 100 permit ip any any
> precedence
> > > > > critical
> > > > > > access-list 100 permit udp any any range
> 16384
> > > > > 32767
> > > > > > access-list 100 permit ip any any dscp ef
> > > > > > access-list 100 permit udp any range 16384
> > > 32767
> > > > > any
> > > > > > access-list 101 permit tcp any range 2000
> 2002
> > > any
> > > > > > access-list 101 permit tcp any any range
> 2000
> > > 2002
> > > > > > access-list 101 permit tcp any range 11000
> > > 11999
> > > > > any
> > > > > > access-list 101 permit tcp any any range
> 11000
> > > > > 11999
> > > > > > access-list 101 permit tcp any any eq 1720
> > > > > > access-list 101 permit tcp any eq 1720 any
> > > > > >
> > > > > >
> > > > > > --- Adarsh Singh <adarshs@hclinfinet.net>
> > > wrote:
> > > > > > > Hi Erik
> > > > > > >
> > > > > > > I am getting the matched packets on the
> > > > > access-list
> > > > > > > for the ip packets, but
> > > > > > > still when i start the voice
> conversation
> > > > > between
> > > > > > > the two boxes, it is not
> > > > > > > reserving the 40 Kbps , when the ftp is
> > > going on
> > > > > ,
> > > > > > > the traffic reaches to
> > > > > > > 62 Kbps , and the voice breaks while
> talking
> > > > > ,pls do
> > > > > > > suggest what to do.
> > > > > > >
> > > > > > > Rgds
> > > > > > > Adarsh Singh
> > > > > > > ----- Original Message -----
> > > > > > > From: "Erick B." <erickbe@yahoo.com>
> > > > > > > To: "Adarsh Singh"
> <adarshs@hclinfinet.net>;
> > > > > "CCIE
> > > > > > > Group Study (E-mail)"
> > > > > > > <ccielab@groupstudy.com>
> > > > > > > Sent: Friday, October 04, 2002 10:54 AM
> > > > > > > Subject: Re: CBWFQ not working on 1603
> for
> > > > > > > VOICE--HELP NEEDED URGENTLY
> > > > > > >
> > > > > > >
> > > > > > > > Thats because UDP is being matched by
> the
> > > > > first
> > > > > > > entry
> > > > > > > > in the ACL. ACL stops processing after
> a
> > > > > match. IP
> > > > > > > > covers ICMP, UDP, and TCP.
> > > > > > > >
> > > > > > > > --- Adarsh Singh
> <adarshs@hclinfinet.net>
> > > > > wrote:
> > > > > > > > > Hi ,=20
> > > > > > > > >
> > > > > > > > > I have been trying to implement
> CBWFQ
> > > > > between
> > > > > > > two
> > > > > > > > > cisco 1603 routers.
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > PC
> > > > > > > > > |
> > > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
>
OAHO(router1)(serial0)------backtoback-------(serial0)OAREMOTE(router2)--=
> > > > > > > > > --VOIPBOX1(10.66.6.126)
> > > > > > > > > |
> > > > > > > (64
> > > > > > > > > Kbps) =
> > > > > > > > >
> > > > > > > |
> > > > > > > > > |
> > > > > > > > > =
> > > > > > > > >
> > > > > > > > > PC
> > > > > > > > >
> > > > > > > > > VOIPBOX2
> > > > > > > > > (10.66.6.35)
> > > > > > > > >
> > > > > > > > > Now the default queing for the two
> > > routers
> > > > > is
> > > > > > > > > Weighted fair quwing .
> > > > > > > > >
> > > > > > > > > Now i have reserved 30 Kbps
> bandwidth
> > > > > between
> > > > > > > the
> > > > > > > > > two router for the =
> > > > > > > > > voice traffic , the voipbox is uing
> UDP
> > > > > ports
> > > > > > > > > greater than 20000.
> > > > > > > > >
> > > > > > > > > So after configuring the routers , i
> do
> > > a
> > > > > > > multiple
> > > > > > > > > ftp sessions between =
> > > > > > > > > the two PC, so that the traffic
> between
> > > the
> > > > > two
> > > > > > > > > serial interfaces =
> > > > > > > > > touches 62 Kbps .
> > > > > > > > >
> > > > > > > > > Now when i start talking between
> the
> > > two
> > > > > VOIP
> > > > > > > boxes
> > > > > > > > > , i dont see the =
> > > > > > > > > CBWFQ kicking in & reserving the
> > > necessary
> > > > > > > bandwidth
> > > > > > > > > as i have =
> > > > > > > > > provisioned .
> > > > > > > > >
> > > > > > > > > I am enclosing both the router
> > > configuration
> > > > > :
> > > > > > > > >
> > > > > > > > > CONFIG OF OAHO=20
> > > > > > > > >
> > > > > > > > > OAHO=20
> > > > > > > > >
> > > > > > > > > sh ru=20
> > > > > > > > > Building configuration...
> > > > > > > > >
> > > > > > > > > Current configuration : 1146 bytes
> > > > > > > > > !
> > > > > > > > > version 12.1
> > > > > > > > > no service single-slot-reload-enable
> > > > > > > > > service timestamps debug uptime
> > > > > > > > > service timestamps log uptime
> > > > > > > > > no service password-encryption
> > > > > > > > > !
> > > > > > > > > hostname OAHO
> > > > > > > > > !
> > > > > > > > > !
> > > > > > > > > !
> > > > > > > > > class-map voice
> > > > > > > > > match access-group 101
> > > > > > > > > !
> > > > > > > > > !
> > > > > > > > > policy-map test
> > > > > > > > > class voice
> > > > > > > > > priority 40
> > > > > > > > > !
> > > > > > > > > ip subnet-zero
> > > > > > > > > ip tftp source-interface Ethernet0
> > > > > > > > > !
> > > > > > > > > !
> > > > > > > > > interface Ethernet0
> > > > > > > > > description connected to
> EthernetLAN_1
> > > > > > > > > ip address 10.66.6.33
> 255.255.255.248
> > > > > > > > > no cdp enable
> > > > > > > > > !
> > > > > > > > > interface Serial0
> > > > > > > > > description connected to Internet
> > > > > > > > > bandwidth 64
> > > > > > > > > ip address 10.66.2.98
> 255.255.255.252
> > > > > > > > > no ip route-cache
> > > > > > > > > no ip mroute-cache
> > > > > > > > > service-policy output test=20
> > > > > > > > > load-interval 30
> > > > > > > > > max-reserved-bandwidth 90
> > > > > > > > > !
> > > > > > > > > interface BRI0
> > > > > > > > > no ip address
> > > > > > > > > shutdown
> > > > > > > > > ip classless
> > > > > > > > > ip route 0.0.0.0 0.0.0.0 10.66.2.97
> > > > > > > > > no ip http server
> > > > > > > > > !
> > > > > > > > > access-list 101 permit ip host
> > > 10.66.6.35
> > > > > host
> > > > > > > > > 10.66.6.126
> > > > > > > > > access-list 101 permit udp host
> > > 10.66.6.35
> > > > > gt
> > > > > > > 20000
> > > > > > > > > host 10.66.6.126 gt =
> > > > > > > > > 20000
> > > > > > > > > dialer-list 1 protocol ip permit
> > > > > > > > > tftp-server
> flash:c1600-sy-mz.121-15.bin
> > > > > > > > > !
> > > > > > > > > line con 0
> > > > > > > > > exec-timeout 0 0
> > > > > > > > > password vpn
> > > > > > > > > login
> > > > > > > > > line vty 0 4
> > > > > > > > > exec-timeout 60 0
> > > > > > > > > password vpn
> > > > > > > > > login
> > > > > > > > > transport preferred none
> > > > > > > > > !
> > > > > > > > > end
> > > > > > > > >
> > > > > > > > > OAHO# show po
> > > > > > > > > OAHO# show policy-map=20
> > > > > > > > > Policy Map test
> > > > > > > > > Weighted Fair Queueing
> > > > > > > > > Class voice=20
> > > > > > > > > Strict Priority
> > > > > > > > > Bandwidth 40 (kbps)
> > > > > > > > >
> > > > > > > > > OAHO#show policy-map=20
> > > > > > > > > Policy Map test
> > > > > > > > > Weighted Fair Queueing
> > > > > > > > > Class voice=20
> > > > > > > > > Strict Priority
> > > > > > > > > Bandwidth 40 (kbps)
> > > > > > > > >
> > > > > > > > > OAHO#show policy-map int se 0
> > > > > > > > > OAHO#show int se 0
> > > > > > > > > Serial0 is up, line protocol is
> up=20
> > > > > > > > > Hardware is QUICC Serial
> > > > > > > > > Description: connected to Internet
> > > > > > > > > Internet address is 10.66.2.98/30
> > > > > > > > > MTU 1500 bytes, BW 64 Kbit, DLY
> 20000
> > > > > usec,=20
> > > > > > > > > reliability 255/255, txload
> 3/255,
> > > > > rxload
> > > > > > > 3/255
> > > > > > > > > Encapsulation HDLC, loopback not
> set
> > > > > > > > > Keepalive set (10 sec)
> > > > > > > > > Last input 00:00:00, output
> 00:00:00,
> > > > > output
> > > > > > > hang
> > > > > > > > > never
> > > > > > > > > Last clearing of "show interface"
> > > counters
> > > > > > > > > 00:08:54
> > > > > > > > > Input queue: 0/75/0/0
> > > > > > > (size/max/drops/flushes);
> > > > > > > > > Total output drops: 0
> > > > > > > > > Queueing strategy: fifo
> > > > > > > > > Output queue :0/40 (size/max)
> > > > > > > > > 30 second input rate 1000
> bits/sec, 4
> > > > > > > packets/sec
> > > > > > > > > 30 second output rate 62000
> bits/sec,
> > > 3
> > > > > > > > > packets/sec
> > > > > > > > > 816 packets input, 39184 bytes,
> 0
> > > no
> > > > > buffer
> > > > > > > > > Received 69 broadcasts, 0
> runts, 0
> > > > > giants,
> > > > > > > 0
> > > > > > > > > throttles
> > > > > > > > > 0 input errors, 0 CRC, 0 frame,
> 0
> > > > > overrun,
> > > > > > > 0
> > > > > > > > > ignored, 0 abort
> > > > > > > > > 717 packets output, 46507
> bytes, 0
> > > > > > > underruns
> > > > > > > > > 0 output errors, 0 collisions,
> 1
> > > > > interface
> > > > > > > > > resets
> > > > > > > > > 0 output buffer failures, 0
> output
> > > > > buffers
> > > > > > > > > swapped out
> > > > > > > > > 6 carrier transitions
> > > > > > > > > DCD=3Dup DSR=3Dup DTR=3Dup
> > > RTS=3Dup
> > > > > > > > > CTS=3Dup
> > > > > > > > > --
> > > > > > > > >
> > > > > > > > > OAHO#show queue se 0
> > > > > > > > > Show queue not supported with FIFO
> > > queueing
> > > > > > > > >
> > > > > > > > > OAREMOTE CONFIG
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > sh ru=20
> > > > > > > > > Building configuration...
> > > > > > > > >
> > > > > > > > > Current configuration : 1316 bytes
> > > > > > > > > !
> > > > > > > > > version 12.1
> > > > > > > > > no service single-slot-reload-enable
> > > > > > > > > service timestamps debug uptime
> > > > > > > > > service timestamps log uptime
> > > > > > > > > no service password-encryption
> > > > > > > > > !
> > > > > > > > > hostname OAREMOTE
> > > > > > > > > !
> > > > > > > > > enable secret 5
> > > > > $1$r1WR$YWvapuJdPcjur/4S6MRKv.
> > > > > > > > > !
> > > > > > > > > username dlinpc password 0 npc
> > > > > > > > > username noidad32 password 0 d32
> > > > > > > > > !
> > > > > > > > > class-map voice
> > > > > > > > > match access-group 101
> > > > > > > > > !
> > > > > > > > > !
> > > > > > > > > policy-map test
> > > > > > > > > class voice
> > > > > > > > > priority 40
> > > > > > > > > ip subnet-zero
> > > > > > > > > !
> > > > > > > > > isdn switch-type basic-net3
> > > > > > > > > !
> > > > > > > > > !
> > > > > > > > > !
> > > > > > > > > interface Ethernet0
> > > > > > > > > ip address 10.66.6.121
> 255.255.255.248
> > > > > > > > > ip nat inside
> > > > > > > > > no cdp enable
> > > > > > > > > !
> > > > > > > > > interface Serial0
> > > > > > > > > description connected to Infinet
> 64K
> > > leased
> > > > > > > line
> > > > > > > > > for vpn
> > > > > > > > > bandwidth 64
> > > > > > > > > ip address 10.66.2.122
> 255.255.255.252
> > > > > > > > > no ip route-cache
> > > > > > > > > no ip mroute-cache
> > > > > > > > > load-interval 30
> > > > > > > > > max-reserved-bandwidth 90
> > > > > > > > > service-policy output test
> > > > > > > > > clockrate 64000
> > > > > > > > > !
> > > > > > > > > interface BRI0
> > > > > > > > > description connected to NPC/D32
> > > > > > > > > no ip address
> > > > > > > > > encapsulation ppp
> > > > > > > > > isdn switch-type basic-net3
> > > > > > > > > no fair-queue
> > > > > > > > > no cdp enable
> > > > > > > > > !
> > > > > > > > > ip classless
> > > > > > > > > ip route 0.0.0.0 0.0.0.0 10.66.2.121
> > > > > > > > > no ip http server
> > > > > > > > > !
> > > > > > > > > access-list 101 permit ip host
> > > 10.66.6.126
> > > > > host
> > > > > > > > > 10.66.6.35
> > > > > > > > > access-list 101 permit udp host
> > > 10.66.6.126
> > > > > gt
> > > > > > > 20000
> > > > > > > > > host 10.66.6.36 gt =
> > > > > > > > > 20000
> > > > > > > > > dialer-list 1 protocol ip permit
> > > > > > > > > !
> > > > > > > > > line con 0
> > > > > > > > > exec-timeout 0 0
> > > > > > > > > password 111
> > > > > > > > > login
> > > > > > > > > line vty 0 password 111
> > > > > > > > > login
> > > > > > > > > !
> > > > > > > > > end
> > > > > > > > >
> > > > > > > > > OAREMOTE# show po
> > > > > > > > > OAREMOTE# show policy-map=20
> > > > > > > > > Policy Map test
> > > > > > > > > Weighted Fair Queueing
> > > > > > > > > Class voice=20
> > > > > > > > > Strict Priority
> > > > > > > > > Bandwidth 40 (kbps)
> > > > > > > > > OAREMOTE#show po
> > > > > > > > > OAREMOTE#show policy-map int se 0
> > > > > > > > > Serial0 output : test
> > > > > > > > > Weighted Fair Queueing
> > > > > > > > > Class voice=20
> > > > > > > > > Strict Priority
> > > > > > > > > Output Queue: Conversation
> 24=20
> > > > > > > > > Bandwidth 40 (kbps) Packets
> > > Matched
> > > > > 40
> > > > > > > > > (total drops/bytes drops)
> 5/380
> > > > > > > > > OAREMOTE#sjh=08 =08=08 =08=FF
> > > > > > > > >
> > > > > > > > > User Access Verification
> > > > > > > > >
> > > > > > > > > Password: =07=FF
> > > > > > > > > OAHO>telnet 10.66.6.12=08 =08=08
> =08121
> > > > > > > > > Trying 10.66.6.121 ... Open
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > =20
> > > > > > > > >
> > > > > > > > > OAREMOTE#show policy-map=20
> > > > > > > > > Policy Map test
> > > > > > > > > Weighted Fair Queueing
> > > > > > > > > Class voice=20
> > > > > > > > > Strict Priority
> > > > > > > > > Bandwidth 40 (kbps)
> > > > > > > > > OAREMOTE#show po
> > > > > > > > > OAREMOTE#show policy-map int se 0
> > > > > > > > > Serial0 output : test
> > > > > > > > > Weighted Fair Queueing
> > > > > > > > > Class voice=20
> > > > > > > > > Strict Priority
> > > > > > > > > Output Queue: Conversation
> 24=20
> > > > > > > > > Bandwidth 40 (kbps) Packets
> > > Matched
> > > > > 40
> > > > > > > > > (total drops/bytes drops)
> 5/380
> > > > > > > > > =20
> > > > > > > > > =20
> > > > > > > > > =20
> > > > > > > > > =20
> > > > > > > > > Now when i even see the access-list
> 101
> > > , i
> > > > > dont
> > > > > > > see
> > > > > > > > > any match for the =
> > > > > > > > > UDP packets while talking , i fail
> to
> > > > > undertand
> > > > > > > that
> > > > > > > > > because when i do =
> > > > > > > > > debug ip packet detail , i see the
> udp
> > > ports
> > > > > > > been
> > > > > > > > > used while talking =
> > > > > > > > > between the voip box .
> > > > > > > > > =20
> > > > > > > > > Can some one help me out with
> > > this....needed
> > > > > > > help
> > > > > > > > > urgently .
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > >
> > >
> __________________________________________________
> > > > > > > > Do you Yahoo!?
> > > > > > > > New DSL Internet Access from SBC &
> Yahoo!
> > > > > > > > http://sbc.yahoo.com
> > > > > >
> > > > > >
> > > > > >
> > >
> __________________________________________________
> > > > > > Do you Yahoo!?
> > > > > > New DSL Internet Access from SBC & Yahoo!
> > > > > > http://sbc.yahoo.com
> > > >
> > > >
> > > >
> __________________________________________________
> > > > Do you Yahoo!?
> > > > Faith Hill - Exclusive Performances, Videos &
> More
> > > > http://faith.yahoo.com
> > >
> >
> >
> > __________________________________________________
> > Do you Yahoo!?
> > Faith Hill - Exclusive Performances, Videos & More
> > http://faith.yahoo.com
>
This archive was generated by hypermail 2.1.4 : Tue Nov 05 2002 - 08:35:41 GMT-3