From: Larry Letterman (lletterm@cisco.com)
Date: Tue Sep 17 2002 - 22:01:22 GMT-3
sh cam dy is used on cat 6500 running catos...
Hongtu Wang wrote:
>Hi, Becky,
>
>Normally "show cam dy" is used on Cat4K/5K. I have a 7603 router with 2 Cat 6000 supervisor engine 2 (WS-X6K-S2U-MSFC2) and 1 48 ports 10/100 module. I put a native IOS image on it. The show info as:
>
>7603#sh module
>
>Mod Ports Card Type Model Serial No.
>
>--- ----- -------------------------------------- ------------------ -----------
>
> 1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 SAL06261UET
>
> 2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-S2U-MSFC2 SAL06261UJL
>
> 3 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD061700FY
>
>
>
>Mod MAC addresses Hw Fw Sw Status
>
>--- ---------------------------------- ------ ------------ ------------ -------
>
> 1 0009.1243.9d4c to 0009.1243.9d4d 3.7 6.1(3) 7.2(0.90) Ok
>
> 2 0006.d65b.7f30 to 0006.d65b.7f31 3.7 6.1(3) 7.2(0.90) Ok
>
> 3 0002.7ee3.41f4 to 0002.7ee3.4223 4.3 6.3(1) 7.2(0.90) Ok
>
>
>
>Mod Sub-Module Model Serial Hw Status
>
>--- --------------------------- --------------- --------------- ------- -------
>
> 1 Policy Feature Card 2 WS-F6K-PFC2 SAL06261MPV 3.2 Ok
>
> 1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K60 2.3 Ok
>
> 2 Policy Feature Card 2 WS-F6K-PFC2 SAL06261M2X 3.2 Other
>
> 2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K4Z 2.3 Ok
>
>7603#sh module
>
>Mod Ports Card Type Model Serial No.
>
>--- ----- -------------------------------------- ------------------ -----------
>
> 1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 SAL06261UET
>
> 2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-S2U-MSFC2 SAL06261UJL
>
> 3 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD061700FY
>
>
>
>Mod MAC addresses Hw Fw Sw Status
>
>--- ---------------------------------- ------ ------------ ------------ -------
>
> 1 0009.1243.9d4c to 0009.1243.9d4d 3.7 6.1(3) 7.2(0.90) Ok
>
> 2 0006.d65b.7f30 to 0006.d65b.7f31 3.7 6.1(3) 7.2(0.90) Ok
>
> 3 0002.7ee3.41f4 to 0002.7ee3.4223 4.3 6.3(1) 7.2(0.90) Ok
>
>
>
>Mod Sub-Module Model Serial Hw Status
>
>--- --------------------------- --------------- --------------- ------- -------
>
> 1 Policy Feature Card 2 WS-F6K-PFC2 SAL06261MPV 3.2 Ok
>
> 1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K60 2.3 Ok
>
> 2 Policy Feature Card 2 WS-F6K-PFC2 SAL06261M2X 3.2 Other
>
> 2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K4Z 2.3 Ok
>
>7603#sh ver
>
>Cisco Internetwork Operating System Software
>
>IOS (tm) c6sup2_rp Software (c6sup2_rp-JO3SV-M), Version 12.1(12c)E1, EARLY DEP)
>
>TAC Support: http://www.cisco.com/tac
>
>Copyright (c) 1986-2002 by cisco Systems, Inc.
>
>Compiled Wed 07-Aug-02 17:42 by eaarmas
>
>Image text-base: 0x40008980, data-base: 0x419C6000
>
>
>
>ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
>
>BOOTLDR: c6sup2_rp Software (c6sup2_rp-JO3SV-M), Version 12.1(12c)E1, EARLY DEP)
>
>
>
>7603 uptime is 1 week, 1 day, 1 hour, 56 minutes
>
>System returned to ROM by power-on (SP by power-on)
>
>System image file is "slot0:c6sup22-jo3sv-mz.121-12c.E1"
>
>
>
>cisco Catalyst 6000 (R7000) processor with 489472K/34816K bytes of memory.
>
>Processor board ID SAL06251K60
>
>R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
>
>Last reset from power-on
>
>Bridging software.
>
>X.25 software, Version 3.0.0.
>
>SuperLAT software (copyright 1990 by Meridian Technology Corp).
>
>TN3270 Emulation software.
>
>1 Virtual Ethernet/IEEE 802.3 interface(s)
>
>48 FastEthernet/IEEE 802.3 interface(s)
>
>4 Gigabit Ethernet/IEEE 802.3 interface(s)
>
>381K bytes of non-volatile configuration memory.
>
>
>
>16384K bytes of Flash internal SIMM (Sector size 512K).
>
>Configuration register is 0x102
>
>
>
>7603#
>
>7603#
>
>7603#sh cam ?
>
>% Unrecognized command
>
>7603#sh cam
>
>As you can see, when I typed "sh cam ?", it said "% Unrecognized command". Can you or anybody tell me how to find out cam table on it?
>
>Thanks
>
>Hongtu Wang
>
>
>
>----- Original Message -----
>From: "Becky Qiang" <becky.qiang@wincomsystems.com>
>To: "Hongtu Wang" <wht_wh@sympatico.ca>; <ccielab@groupstudy.com>
>Sent: Tuesday, September 17, 2002 6:58 PM
>Subject: Re: how to show cam table on 6500
>
>
>>Hi Hongtu:
>>
>>You can do a 'show cam dy' to show the cam table. Also, you can do a 'show
>>cam ?' to see other show cam options.
>>
>>Becky
>>
>>
>>
>>----- Original Message -----
>>From: "Hongtu Wang" <wht_wh@sympatico.ca>
>>To: <ccielab@groupstudy.com>
>>Sent: Monday, September 16, 2002 4:40 PM
>>Subject: how to show cam table on 6500
>>
>>
>>>We have a cat 6500 running native IOS. Can anybody tell me how to show cam
>>>
>>table on it?
>>
>>>Thanks
>>>
--Larry Letterman Network Engineer Cisco Systems Inc.
This archive was generated by hypermail 2.1.4 : Mon Oct 07 2002 - 07:43:55 GMT-3