From: Colin Barber (Colin.Barber@xxxxxxxxxxxxxx)
Date: Tue Aug 27 2002 - 04:56:21 GMT-3
I thought that the original question was to enable IPX connectivity without
configuring IPX on the serial interface. Obviously if you can use IPX on the
serial interface then there is no need for the tunnel interfaces.
The two routers could be connected multiple hops in which the intermediate
routers do not support IPX. In this case the tunnel interfaces is the only
option.
Colin.
-----Original Message-----
From: Peng Zheng [mailto:zpnist@yahoo.com]
Sent: 26 August 2002 17:08
To: Colin Barber; steven.j.nelson@bt.com; putti@ait.co.th;
ccielab@groupstudy.com
Subject: RE: ipx tunneling
I have a question. WHy don't congiure ipxwan under
serial 0 directly?
--- Colin Barber <Colin.Barber@telewest.co.uk> wrote:
> Sample config using IPXWAN:
>
> R1
> ipx internal-network 1
> Int ser0
> ip address 192.168.1.1 255.255.255.252
> Int Tunnel 0
> ipx ipxwan 0 unnumbered
> tunnel source 192.168.1.1 (or tunnel source serial
> 0)
> tunnel destination 192.168.1.2
>
> R2
> ipx internal-network 2
> Int ser0
> ip address 192.168.1.2 255.255.255.252
> Int Tunnel 0
> ipx ipxwan 0 unnumbered
> tunnel source 192.168.1.2
> tunnel destination 192.168.1.1
>
> -----Original Message-----
> From: steven.j.nelson@bt.com
> [mailto:steven.j.nelson@bt.com]
> Sent: 26 August 2002 10:12
> To: Colin.Barber@telewest.co.uk; putti@ait.co.th;
> ccielab@groupstudy.com
> Subject: RE: ipx tunneling
>
>
> Colin,
>
> However if no native IPX is allowed, i.e no ipx
> address configured on the
> tunnel then you could use IPXWAN unnumbered, you
> will have to add an
> internal network address to the config.
>
> Cheers
>
> Steve
>
> -----Original Message-----
> From: Colin Barber
> [mailto:Colin.Barber@telewest.co.uk]
> Sent: 26 August 2002 09:51
> To: Putti Dhamrongsirivadh; ccielab@groupstudy.com
> Subject: RE: ipx tunneling
>
>
> Tunnelling is correct.
>
> R1
> Int ser0
> ip address 192.168.1.1 255.255.255.252
> Int Tunnel 0
> ipx network CC
> tunnel source 192.168.1.1 (or tunnel source serial
> 0)
> tunnel destination 192.168.1.2
>
> R2
> Int ser0
> ip address 192.168.1.2 255.255.255.252
> Int Tunnel 0
> ipx network CC
> tunnel source 192.168.1.2
> tunnel destination 192.168.1.1
>
>
> Both routers will communicate IPX with each other
> over network CC (tunnel
> interface).
>
> Colin
>
> -----Original Message-----
> From: Putti Dhamrongsirivadh
> [mailto:putti@ait.co.th]
> Sent: 26 August 2002 23:28
> To: ccielab@groupstudy.com
> Subject: ipx tunneling
>
>
> Hi
>
> I have a scenario:
>
>
>
> ipx net AA no ipx network ipx net
> BB
>
--------------R1----------------------R2--------------
> e0 s0 s0
> e0
>
>
> How can we configure R1 and R2 so that R2 can see
> ipx net AA in ipx routing
> table? I heard that we need to use tunneling between
> R1 and R2. Is that
> correct? Could someone give me a sample
> configuration?
>
> thanks,
> Putti
>
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:39 GMT-3