RE: ipx tunneling

From: Colin Barber (Colin.Barber@xxxxxxxxxxxxxx)
Date: Mon Aug 26 2002 - 06:40:33 GMT-3

• Next message: M. Nabelsi: "lab in Sao Paolo"
• Previous message: steven.j.nelson@xxxxxx: "RE: ipx tunneling"
• Maybe in reply to: Putti Dhamrongsirivadh: "ipx tunneling"
• Next in thread: Mingzhou Nie: "RE: ipx tunneling"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

   
Sample config using IPXWAN:

R1
ipx internal-network 1
Int ser0
  ip address 192.168.1.1 255.255.255.252
Int Tunnel 0
  ipx ipxwan 0 unnumbered
  tunnel source 192.168.1.1 (or tunnel source serial 0)
  tunnel destination 192.168.1.2

R2
ipx internal-network 2
Int ser0
  ip address 192.168.1.2 255.255.255.252
Int Tunnel 0
  ipx ipxwan 0 unnumbered
  tunnel source 192.168.1.2
  tunnel destination 192.168.1.1

-----Original Message-----
From: steven.j.nelson@bt.com [mailto:steven.j.nelson@bt.com]
Sent: 26 August 2002 10:12
To: Colin.Barber@telewest.co.uk; putti@ait.co.th; ccielab@groupstudy.com
Subject: RE: ipx tunneling

Colin,

However if no native IPX is allowed, i.e no ipx address configured on the
tunnel then you could use IPXWAN unnumbered, you will have to add an
internal network address to the config.

Cheers

Steve

-----Original Message-----
From: Colin Barber [mailto:Colin.Barber@telewest.co.uk]
Sent: 26 August 2002 09:51
To: Putti Dhamrongsirivadh; ccielab@groupstudy.com
Subject: RE: ipx tunneling

Tunnelling is correct.

R1
Int ser0
  ip address 192.168.1.1 255.255.255.252
Int Tunnel 0
  ipx network CC
  tunnel source 192.168.1.1 (or tunnel source serial 0)
  tunnel destination 192.168.1.2

R2
Int ser0
  ip address 192.168.1.2 255.255.255.252
Int Tunnel 0
  ipx network CC
  tunnel source 192.168.1.2
  tunnel destination 192.168.1.1

Both routers will communicate IPX with each other over network CC (tunnel
interface).

Colin

-----Original Message-----
From: Putti Dhamrongsirivadh [mailto:putti@ait.co.th]
Sent: 26 August 2002 23:28
To: ccielab@groupstudy.com
Subject: ipx tunneling

Hi

I have a scenario:

ipx net AA no ipx network ipx net BB
--------------R1----------------------R2--------------
               e0 s0 s0 e0

How can we configure R1 and R2 so that R2 can see ipx net AA in ipx routing
table? I heard that we need to use tunneling between R1 and R2. Is that
correct? Could someone give me a sample configuration?

thanks,
Putti

• Next message: M. Nabelsi: "lab in Sao Paolo"
• Previous message: steven.j.nelson@xxxxxx: "RE: ipx tunneling"
• Maybe in reply to: Putti Dhamrongsirivadh: "ipx tunneling"
• Next in thread: Mingzhou Nie: "RE: ipx tunneling"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:37 GMT-3