From: Balaji Siva (bsivasub@xxxxxxxxx)
Date: Sun Aug 11 2002 - 13:52:51 GMT-3
check this out
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121
t/121t5/dtpoli.htm#25923
12.1(5)T should have it for 2600/3600... i didn't try it in the lab but i
don't see any reason to.
Balaji
-----Original Message-----
From: \mit Askan (TK-Network Gvz|mleri)
[mailto:umit.askan@probil.com.tr]
Sent: Sunday, August 11, 2002 8:23 AM
To: 'Balaji Siva'
Cc: Ccie (E-mail)
Subject: RE: QOS Question from Routopia LAB 3
Hi,
please correct me if I am wrong,
I couldn't find the police command for CBWFQ at 12.1 command ref.
I think this command is only for 7500 series at special versions of
12.1. And at the 12.2.
At the situation we are not responsible for this command ?
Best Regards
umit
-----Original Message-----
From: Balaji Siva [mailto:bsivasub@cisco.com]
Sent: Sunday, August 11, 2002 04:53
To: William lu; Akhilesh Verma; ccielab@groupstudy.com
Subject: RE: QOS Question from Routopia LAB 3
the question is vague as it could be just LLQ for ping/bgp ..and the
rest
class-default ..if the question had just mentioned that these things are
applicable only at times of congestion.
but since it didn't..
how about this
class-map ping
match access-group 101 <--- 101 matches icmp
class-map bgp
match access-group 102 <---- 102 matches bgp
policy-map ccie
class ping
police xxxx xxxxxx <-----10 % policer
class bgp
police xxxx xxxx <----- 30 % policer
int s0
service output ccie
Regards
Balaji
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
William lu
Sent: Saturday, August 10, 2002 9:22 PM
To: Akhilesh Verma; ccielab@groupstudy.com
Subject: Re: QOS Question from Routopia LAB 3
Hi,
I would use both technique complete this scenario:
1. Use CAR to limit the bandwidth used in CBWFQ. The
default bandwidth of physical interface be used for
the bandwidth calculation if you did not use TS or
CAR. (You may no be able to use bandwidth interface
command, which use for metric only).
2. Use CBWFQ to assign the bandwidth to each type of
traffic, which specify by CAR.
This is my implementation of the question. hope have
better one.
LUW.
Akhilesh, Where can I find this lab scenario? I'd like
to play with this completed lab.
--- Akhilesh Verma <akverma@cisco.com> wrote:
> Folks,
> I am working on Routopia LAB 3
and
> I have the following
> question
>
> Configure the serial interface on R6 so that Ping
> traffic can only
> utilize 10% of available bandwidth. Allow BGP to
> utilize no more
> than 20% of available bandwidth. Allow all other
> traffic to utilize up
> to 70% of available link capacity.
>
>
> Now ordinarily One would think that this is
> classification and not
> policing . Would you do CBWFQ here or CAR ?
>
> TIA
>
> Akhilesh
> ------------------------------------------------
> ------------------------------------------------
> Akhilesh Verma,
> Cisco Systems Inc.
> Systems Engineer
> 771,Alder Drive,
> Milpitas,CA-95035
> Pager:800-365-4578
> Direct: 408-853-9033
> Mobile: 510-501-1182.
> E-mail: akverma@cisco.com
>
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:23 GMT-3