From: Rick Lowery (ccie_2003@xxxxxxxxxxx)
Date: Tue Aug 06 2002 - 22:34:04 GMT-3
Actually, mutlple people were right here... You must thank Cisco for major
changes in their code between 12.1(8)EA1c AND 12.1(9)EA1c in (8) it was done
at the exec priv mode and in (9) it is done at the configuration mode...
Also, just wait until you experience upgrading your code.. That is also
fun... I recommend get your box to 12.1(9).....
----- Original Message ----- From: "Imo Etuk" <ietuk@comcast.net>
To: "Ashok.Gupta" <Ashok.Gupta@gmconsultants.com>; "'Michael Snyder'"
<msnyder@ldd.net>; "'Todd Carswell'" <acarswell@nc.rr.com>
Cc: <ccielab@groupstudy.com>
Sent: Tuesday, August 06, 2002 10:51 PM
Subject: RE: Basic config of the cat 3550
> Here ya go
>
> conf t
>
> (config)#int vlan x
> (config)# ip address x.x.x.x y.y.y.y
> (config)# no shut
>
> exit
>
> #vlan databse
> #vlan x name ZZZZ
>
> exit
>
> (config)# int gig x
> (config)# switchport access vlan x
> (config)# speed x
> (config)# duplex x
> (config)# no shut
>
> Thats all you need - hope this helps. I with these everyday :)
>
> Imo
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Ashok.Gupta
> Sent: Tuesday, August 06, 2002 3:46 PM
> To: 'Michael Snyder'; 'Todd Carswell'
> Cc: ccielab@groupstudy.com
> Subject: RE: Basic config of the cat 3550
>
>
> conf t
>
> interface Vlan1
> ip address x.x.x.x y.y.y.y
>
> Rem dot1q is default.
>
> other commands need to know
>
> switchport multi vlan x,y,z
> switchport mode multi
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Michael Snyder
> Sent: 06 August 2002 21:34
> To: 'Todd Carswell'
> Cc: ccielab@groupstudy.com
> Subject: RE: Basic config of the cat 3550
>
>
> Config t
> Int vlan 1
>
> Etc.
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Todd Carswell
> Sent: Tuesday, August 06, 2002 2:28 PM
> To: ccielab@groupstudy.com
> Subject: Basic config of the cat 3550
>
> All,
>
> Allrighty, I've finally got my paws on a catalyst 3550. I've accessed
> the software config guide for the 3550 on the Doc CD but things just
> ain't quite right!
>
> The Doc CD instructs the user to access the vlan-config mode by typing
> in the following global config command...
>
> vlan <vlan id>
>
>
> Here's what I'm getting from the switch...
>
> cat3550(config)# vlan 100 ?
> Unrecognized Command
>
>
> I'm definitely missing a step. Could someone point me in the right
> direction? I'm hoping that CCO has a page that walks the user through
> some basic setup configs for the cat3550.
>
> Thanks for the help!
>
> Todd Carswell
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:18 GMT-3