From: William lu (mailluw@xxxxxxxxx)
Date: Mon Aug 05 2002 - 01:55:59 GMT-3
Hi Armand,
In order to verify the solution for this issue, I
built your scenario with the TUNNEL solution and it
works just fine.
The problem in your configuration is you can not use
summary address in R6 to summary a OSPF route out of
OSPF domain. Also you can not use area range to
summarize 135.4.24.0/27 for area 0 in R4. Too long to
explain why here.
Solution:
1. Build a tunnel between R5 and R6 with any IGP
protocols other than IGRP and OSPF. Then, send
135.4.36.0/29 frm R5 to R6 and redistribute into ospf
as external route in R6.
2. Redistribute 135.4.24.0/27 as connected route with
route-map (it works in 12.1) into ospf domain.
3. At this point, you should have both routes in your
ospf database as external routes by verifying with ip
ospf database command.
4. Finally, you can use following two commands in R6
to summarize them into 24bit class routes:
summary-address 135.4.24.0 255.255.255.0
summary-address 135.4.36.0 255.255.255.0
5. You should see two classful routes in R5's routing
table as follows:
R 135.4.24.0/29 [120/1] via 150.4.1.2, 00:00:02,
Tunnel0
O E2 135.4.24.0/24 [110/20] via 139.11.12.1, 00:00:03,
Serial0
O E2 135.4.36.0/24 [110/20] via 139.11.12.1, 00:00:03,
Serial0
C 135.4.36.0/27 is directly connected, Loopback10
R 198.172.20.0/24 [120/2] via 150.4.1.2, 00:00:04,
Tunnel0
This could be pne of few solutions to make your
scenario works. It is too long to explain why to can
not use other ways to work around. Please contact
Cyscoexpert.com if you need to learn more in detail
for IGP redistribution. They are the best CCIE
training center I knew.
Let me know if it works.
William
--- Armand D <ciscoworks2001@yahoo.com> wrote:
> Hello,
>
> This is a tough one to get working. I have three
> routers one running IGRP the other two in OSPF. I
> have
> searched the archives for solutions and still can't
> get this one to work. Router 5 shows all area 1
> networks /29 with help of "summary-address"
> command. Router 5 does NOT see any Area 0 /27 routes
> in routing table.I have tried the "area 0
> range" command on R4 with no luck. Please look
> at
> my configs and tell me what I'm missing here.
>
> Any help would be appreciated.
>
> R5
> |
> |
> 135.4.56.0/24 IGRP
> |
> |
> R6
> |
> |
> 135.4.36.0/29 OSPF Area 1
> |
> |
> R4
> |
> 135.4.24.0/27 OSPF Area 0
>
>
>
> ====================================
> hostname R5
> !
> ip subnet-zero
> !
> interface Loopback0
> ip address 135.4.5.5 255.255.255.0
> no ip directed-broadcast
> !
> interface Ethernet0/0
> ip address 135.4.56.5 255.255.255.0
> no ip directed-broadcast
> !
> router igrp 10
> network 135.4.0.0
> !
> ip classless
> !
> end
>
> ===================================
> hostname R6
> !
> ip subnet-zero
>
> interface Loopback0
> ip address 135.4.6.6 255.255.255.0
> no ip directed-broadcast
>
> interface Loopback200
> ip address 135.4.66.6 255.255.255.0
> no ip directed-broadcast
> ip ospf network point-to-point
> !
> interface Serial0/0
> description to R4
> ip address 135.4.34.6 255.255.255.248
> no ip directed-broadcast
> encapsulation frame-relay
> ip ospf message-digest-key 2 md5 secure
> ip ospf network broadcast
> ip ospf priority 0
> frame-relay map ip 135.4.34.4 604 broadcast
> frame-relay lmi-type cisco
> !
> interface Ethernet0/1
> description to R5 IGRP
> ip address 135.4.56.6 255.255.255.0
> no ip directed-broadcast
> !
> router ospf 1
> summary-address 135.4.34.0 255.255.255.0
> redistribute igrp 10 metric 1 subnets
> network 135.4.6.6 0.0.0.0 area 1
> network 135.4.34.0 0.0.0.7 area 1
> network 135.4.36.0 0.0.0.255 area 33
> area 0 authentication
> area 1 authentication message-digest
> area 1 virtual-link 135.4.4.4 message-digest-key 2
> md5 secure
> !
> router igrp 10
> redistribute connected
> redistribute ospf 1 metric 1 1 255 255 1
> network 135.4.0.0
>
> ==========================
>
> hostname R4
> !
> ip subnet-zero
> !
> interface Loopback0
> ip address 135.4.4.4 255.255.255.0
> ip ospf priority 255
> !
> interface Serial0/0
> no ip address
> encapsulation frame-relay
> cdp enable
> frame-relay lmi-type cisco
> !
> interface Serial0/0.1 multipoint
> ip address 135.4.34.4 255.255.255.248
> no ip split-horizon
> ip ospf message-digest-key 2 md5 secure
> ip ospf network broadcast
> frame-relay map ip 135.4.34.6 406 broadcast
> !
> interface Ethernet0/1
> description to to R2
> ip address 135.4.24.4 255.255.255.224
> ip ospf authentication-key cisco
> !
> router ospf 1
> area 0 authentication
> area 0 range 135.4.24.0 255.255.255.0 cost 1
> area 1 authentication message-digest
> area 1 virtual-link 135.4.6.6 message-digest-key 2
> md5 secure
> network 135.4.4.4 0.0.0.0 area 0
> network 135.4.24.0 0.0.0.31 area 0
> network 135.4.34.0 0.0.0.7 area 1
> !
> end
>
>
>
>
>
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:16 GMT-3