From: Christopher Jarosz (cajarosz@xxxxxxxxx)
Date: Sat Jul 27 2002 - 21:08:16 GMT-3
Hi Jason !!!
Take a look at the back of the router (the side where the NPs are) to the
right near the power supply. You should see a tag from Cisco systems with a
serial number. On that tag, you'll see the model type. If you don't have
physical access to the router, you'll need to have someone look......I don't
believe that the model class is known via the software......
HTH...
Chrisj
----- Original Message -----
From: "Jason Cash" <cash2001@swbell.net>
To: <ccielab@groupstudy.com>
Sent: Saturday, July 27, 2002 4:25 PM
Subject: Cisco 4000/4500/4500M
> I recently purchased a Cisco 4000 (as indicated in the auction);
> however, upon rcv'ing the routers, it look in the 'sh ver' and diplays
> the following:
>
> fs#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 4500 Software (C4500-JS-M), Version 12.1(15), RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-2002 by cisco Systems, Inc.
> Compiled Mon 13-May-02 18:42 by kellythw
> Image text-base: 0x60008958, data-base: 0x60FD0000
>
> ROM: System Bootstrap, Version 5.2(7b) [mkamson 7b], RELEASE SOFTWARE
> (fc1)
> BOOTLDR: 4500 Bootstrap Software (C4500-BOOT-M), Version 10.3(7),
> RELEASE SOFTWARE (f
> c1)
>
> fs uptime is 5 minutes
> System returned to ROM by power-on
> System image file is "flash:c4500-js-mz.121-15.bin"
>
> cisco 4500 (R4K) processor (revision B) with 32768K/8192K bytes of
> memory.
> Processor board ID 03771215
> R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
> G.703/E1 software, Version 1.0.
> Bridging software.
> X.25 software, Version 3.0.0.
> SuperLAT software (copyright 1990 by Meridian Technology Corp).
> TN3270 Emulation software.
> 2 Ethernet/IEEE 802.3 interface(s)
> 4 Serial network interface(s)
> 128K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash partition 1 (Read/Write)
> 8192K bytes of processor board System flash partition 2 (Read/Write)
> 4096K bytes of processor board Boot flash (Read/Write)
>
> This would indicate that the device is a 4500. So I then wondered if
> the device was a 4500M. It was successful in loading the 4500 IOS image
> (c4500-a3jk8s-mz.122-10b.bin).
>
> My question is two parts. First, do I have a 4500M of a regular 4500
> and what are the differences between the two? I know that the 4500M
> supports a 12.2 code whereas the 4500 does not. Thanks again and here
> is a 'sh ver' with the 4500M IOS loaded:
>
> fs#sh
> 00:02:12: %SYS-5-CONFIG_I: Configured from console by console ver
> Cisco Internetwork Operating System Software
> IOS (tm) 4500 Software (C4500-A3JK8S-M), Version 12.2(10b), RELEASE
> SOFTWARE (fc1)
> Copyright (c) 1986-2002 by cisco Systems, Inc.
> Compiled Thu 11-Jul-02 13:35 by pwade
> Image text-base: 0x60008948, data-base: 0x6120C000
>
> ROM: System Bootstrap, Version 5.2(7b) [mkamson 7b], RELEASE SOFTWARE
> (fc1)
> BOOTLDR: 4500 Bootstrap Software (C4500-BOOT-M), Version 10.3(7),
> RELEASE SOFTWARE (f
> c1)
>
> fs uptime is 2 minutes
> System returned to ROM by reload at 12:59:10 UTC Sun Jun 2 1996
> System image file is "flash:c4500-a3jk8s-mz.122-10b.bin"
>
> cisco 4500 (R4K) processor (revision B) with 32768K/8192K bytes of
> memory.
> Processor board ID 03771215
> R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
> G.703/E1 software, Version 1.0.
> Bridging software.
> X.25 software, Version 3.0.0.
> SuperLAT software (copyright 1990 by Meridian Technology Corp).
> TN3270 Emulation software.
> 2 Ethernet/IEEE 802.3 interface(s)
> 4 Serial network interface(s)
> 128K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash partition 1 (Read/Write)
> 8192K bytes of processor board System flash partition 2 (Read/Write)
> 4096K bytes of processor board Boot flash (Read/Write)
>
> Configuration register is 0x2102
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:36:47 GMT-3