From: Perminder Grewal (percy_gunner@xxxxxxxxxxx)
Date: Sat Jul 20 2002 - 07:38:53 GMT-3
I have had an attempt on this lab and would like to post some issues to the
group to resolve some of them.
C.2) I made the subnet for 150.1.222.0/24 a non-broadcast network to change
the timers; however I put in full-mesh neighbour statements as you would do
for a frame-relay network. Is this OK?
D.1) I know you changed the RIP timers on the IP Cloud to 10 60 60 80. I
made it 10 30 30 40 i.e. 3 times the update interval as this is the baseline
for RIP. I did various debugs and could not verify the timers from the IP
Cloud. Is there a way to do this or am I digging to deep on this issue.
E.3) One-way redistribution from rip to eigrp, also mutual redistribution
between ospf and eigrp. I used tags to avoid routing loops as shown below
router eigrp 100
Redistribute ospf 1 metric 1000 100 255 1 1500 route-map tag11_2_ospf
router ospf 1
Redistribute eigrp 100 subnets tag 11
Route-map tag11_2_ospf deny 10
match tag 11
route-map tag11_2_ospf permit 20
Is this ok?
The biggest challenge was getting all the routes in R1. I had the routes in
the eigrp topology table as Inaccessible due to AD of 170 and Ospf 110. I
changed the distance of all the ospf routes to 171 on R4 and the eigrp
routes came in on R4 and R1 via the tunnel, However my tunnel started to
bounce due to "recursive lookup" and the routes toggled between ospf and
eigrp. The only route that I could not see on R1 was 150.1.30.0/24 from R3.
So I set up an accesss-list and changed the distance as shown below
router ospf 1
distance 171 0.0.0.0 255.255.255.255 1
access-list 1 permit 150.1.30.0
I found the following link about the recursive lookup.
http://www.cisco.com/warp/public/105/gre_flap.html
The external eigrp routes are propagated down the tunnel from R2 to R4 and
enter the route table with AD off (EX) 170, however these routes get flushed
as ospf has the same prefixes with AD of 110. This bounces the tunnel up and
down every time the route table is refreshed between eigrp and ospf. Is my
understanding of this correct?
Cheers
Percy
>From: "Brian McGahan" <brian@cyscoexpert.com>
>Reply-To: "Brian McGahan" <brian@cyscoexpert.com>
>To: "'IPSec'" <ipsec@myrealbox.com>, <ccielab@groupstudy.com>
>Subject: RE: Re: Cyscoexpert Official Configs
>Date: Sun, 14 Jul 2002 15:04:02 -0500
>
> Regarding the 150.1.30.0/24 on R1, if you followed the
>directions carefully there is no way to learn it via OSPF. Area 12
>should be either a stub area or an NSSA. If it is a stub area, R1
>should be filtering out the default route he's learning from R2 so that
>it doesn't appear in the table. NSSA doesn't generate a default route
>by default.
>
> Since R3's Ethernet (30.0/24) should be advertised "without
>using the network statement", you have to redistribute connected. When
>you redistribute connected, this route now becomes a type 5 external
>LSA. Both stub and NSSA areas do not allow type 5 LSA, therefore it
>cannot be learned via OSPF. R1's only option to learn this route is now
>via EIGRP.
>
> This now presents another problem, which is EIGRP's calculation
>of route feasibility. If you have a duplicate longest match through
>another protocol with a lower administrative distance than EIGRP, EIGRP
>will not consider its own route feasible. The only solution here then
>is to change the distance of the 30.0/24 route on R4 to make EIGRP have
>the preferred administrative distance.
>
> Also, we run into the issue here that you cannot change the
>distance of an EIGRP external route on a per route basis. We could
>solve this problem by changing *all* external EIGRP routes to have a
>distance less than 110, however this is a sloppy solution.
>
> Therefore my preferred solution is to raise the distance of the
>OSPF route to be above 170. You can change the distance on a per route
>basis, and it will not affect other path determinations.
>
> Tada! R1 now has reachability to 150.1.30.0/24 via EIGRP.
>
>HTH
>
>Brian McGahan, CCIE #8593
>Director of Design and Implementation
>brian@cyscoexpert.com
>
>CyscoExpert Corporation
>Internetwork Consulting & Training
>http://www.cyscoexpert.com
>Voice: 847.674.3392
>Fax: 847.674.2625
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>IPSec
>Sent: Sunday, July 14, 2002 1:39 AM
>To: nshah@connect.com.au
>Cc: ccielab@groupstudy.com
>Subject: Re: Re: Cyscoexpert Official Configs
>
>Since 150.1.30.0/24 is an E2 network in OSPF, it's not allowed in R1.
>150.1.30.0/24 gets in R1's routing table by EIGRP from redistribution
>from OSPF.
>
>
>-----Original Message-----
>From: "Nick Shah" <nshah@connect.com.au>
>To: "IPSec" <ipsec@myrealbox.com>, <ccielab@groupstudy.com>
>Date: Sun, 14 Jul 2002 16:21:13 +1000
>Subject: Re: Cyscoexpert Official Configs
>
>And how did u get 150.1.30.0/24 into R1 's routing table (via OSPF) ?
>
>Nick
>----- Original Message -----
>From: IPSec <ipsec@myrealbox.com>
>To: <ccielab@groupstudy.com>
>Sent: Sunday, July 14, 2002 3:12 PM
>Subject: Cyscoexpert Official Configs
>
>
> > Hi Group,
> >
> > Here are the official lab solutions:
> >
> > TermServ-34>1
> > [Resuming connection 1 to rack3r1 ... ]
> >
> > R1#sh run
> > Building configuration...
> >
> >
> >
> > Current configuration : 2014 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R1
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0001.0001.0001
> > !
> > !
> > dlsw local-peer peer-id 150.1.1.1
> > dlsw remote-peer 0 tcp 150.1.3.3
> > dlsw icanreach mac-exclusive
> > dlsw icanreach mac-address 7145.a0e3.0000 mask ffff.ffff.0000
> > dlsw bridge-group 1
> > !
> > interface Loopback0
> > ip address 150.1.1.1 255.255.255.0
> > ipx network 1
> > !
> > interface Loopback1
> > ip address 220.1.0.1 255.255.255.0
> > !
> > interface Loopback2
> > ip address 220.1.1.1 255.255.255.0
> > !
> > interface Loopback3
> > ip address 220.1.2.1 255.255.255.0
> > !
> > interface Loopback4
> > ip address 220.1.3.1 255.255.255.0
> > !
> > interface Loopback10
> > ip address 195.1.1.1 255.255.255.0
> > !
> > interface Ethernet0
> > ip address 150.1.10.1 255.255.255.0
> > ipx network 10
> > bridge-group 1
> > !
> > interface Serial0
> > ip address 150.1.14.1 255.255.255.0
> > ip summary-address eigrp 100 220.1.0.0 255.255.252.0 5
> > ipx network 14
> > no fair-queue
> > clockrate 2000000
> > !
> > interface Serial1
> > ip address 150.1.12.1 255.255.255.0
> > ipx network 12
> > clockrate 2000000
> > !
> > interface TokenRing0
> > no ip address
> > shutdown
> > !
> > router eigrp 100
> > network 150.1.14.1 0.0.0.0
> > network 220.1.0.0 0.0.3.255
> > auto-summary
> > no eigrp log-neighbor-changes
> > !
> > router ospf 1
> > router-id 150.1.1.1
> > log-adjacency-changes
> > area 12 nssa
> > network 150.1.1.1 0.0.0.0 area 12
> > network 150.1.12.1 0.0.0.0 area 12
> > !
> > router bgp 1
> > bgp log-neighbor-changes
> > network 195.1.1.0
> > neighbor 150.1.12.2 remote-as 256
> > neighbor 150.1.14.4 remote-as 34
> > neighbor 150.1.14.4 route-map PREPEND out
> > !
> > ip classless
> > ip http server
> > !
> > !
> > ip prefix-list R1_LOOPBACK seq 5 permit 195.1.1.0/24
> > route-map PREPEND permit 10
> > match ip address prefix-list R1_LOOPBACK
> > set as-path prepend 1 1
> > !
> > route-map PREPEND permit 20
> > !
> > !
> > !
> > !
> > !
> > bridge 1 protocol ieee
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R1#
> > TermServ-34>2
> > [Resuming connection 2 to rack3r2 ... ]
> >
> > R2#sh run
> > Building configuration...
> >
> > Current configuration : 2171 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R2
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0002.0002.0002
> > ipx internal-network 2222
> > !
> > !
> > !
> > interface Loopback0
> > ip address 150.1.2.2 255.255.255.0
> > ipx network 2
> > !
> > interface Loopback10
> > ip address 195.1.2.2 255.255.255.0
> > !
> > interface Tunnel0
> > ip address 150.1.24.2 255.255.255.0
> > ipx network 24
> > tunnel source Loopback0
> > tunnel destination 150.1.4.4
> > !
> > interface Ethernet0
> > ip address 150.1.222.2 255.255.255.0
> > no ip redirects
> > ip ospf message-digest-key 1 md5 cisco
> > ip ospf network point-to-multipoint
> > ipx network 222
> > ipx nlsp enable
> > standby 1 ip 150.1.222.1
> > standby 1 priority 50
> > standby 1 preempt
> > standby 1 track Serial0 50
> > !
> > interface Serial0
> > ip address 150.1.12.2 255.255.255.0
> > ipx network 12
> > no fair-queue
> > !
> > interface Serial1
> > no ip address
> > shutdown
> > !
> > router eigrp 100
> > redistribute ospf 1 metric 1 1 1 1 1
> > network 150.1.24.2 0.0.0.0
> > auto-summary
> > no eigrp log-neighbor-changes
> > !
> > router ospf 1
> > router-id 150.1.2.2
> > log-adjacency-changes
> > area 0 authentication
> > area 12 nssa
> > area 51 authentication message-digest
> > area 51 virtual-link 150.1.5.5 authentication-key cisco
> > redistribute eigrp 100 subnets
> > network 150.1.2.2 0.0.0.0 area 51
> > network 150.1.12.2 0.0.0.0 area 12
> > network 150.1.222.2 0.0.0.0 area 51
> > !
> > router bgp 256
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.2.0
> > neighbor 150.1.4.4 remote-as 34
> > neighbor 150.1.4.4 ebgp-multihop 255
> > neighbor 150.1.4.4 update-source Loopback0
> > neighbor 150.1.12.1 remote-as 1
> > neighbor 150.1.12.1 route-map LOCALPREF in
> > neighbor 150.1.222.6 remote-as 256
> > !
> > ip classless
> > ip http server
> > !
> > !
> > ip prefix-list R3_LOOPBACK seq 5 permit 195.1.3.0/24
> > route-map LOCALPREF permit 10
> > match ip address prefix-list R3_LOOPBACK
> > set local-preference 200
> > !
> > route-map LOCALPREF permit 20
> > !
> > !
> > !
> > !
> > ipx router nlsp
> > area-address 0 0
> > !
> > !
> > ipx router rip
> > no network 222
> > !
> > !
> > !
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R2#
> > TermServ-34>3
> > [Resuming connection 3 to rack3r3 ... ]
> >
> > R3#sh run
> > Building configuration...
> >
> >
> >
> > Current configuration : 1973 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R3
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0003.0003.0003
> > !
> > !
> > dlsw local-peer peer-id 150.1.3.3
> > dlsw remote-peer 0 tcp 150.1.1.1
> > dlsw remote-peer 0 frame-relay interface Serial0 304
> > dlsw icannotreach sap F0
> > dlsw bridge-group 1
> > !
> > interface Loopback0
> > ip address 150.1.3.3 255.255.255.0
> > ipx network 3
> > !
> > interface Loopback10
> > ip address 195.1.3.3 255.255.255.0
> > !
> > interface Serial0
> > ip address 150.1.111.3 255.255.255.248
> > encapsulation frame-relay
> > ip ospf authentication-key cisco
> > ip ospf priority 255
> > ipx network 111
> > no ipx split-horizon eigrp 11
> > no arp frame-relay
> > frame-relay map llc2 304 broadcast
> > frame-relay map ip 150.1.111.4 304 broadcast
> > frame-relay map ip 150.1.111.5 305 broadcast
> > frame-relay map ipx 111.0004.0004.0004 304 broadcast
> > frame-relay map ipx 111.0005.0005.0005 305 broadcast
> > no frame-relay inverse-arp
> > frame-relay lmi-type cisco
> > !
> > interface Serial1
> > no ip address
> > shutdown
> > !
> > interface Ethernet0
> > ip address 150.1.30.3 255.255.255.0
> > ipx network 30
> > bridge-group 1
> > !
> > interface BRI0
> > no ip address
> > shutdown
> > isdn x25 static-tei 0
> > !
> > router ospf 1
> > router-id 150.1.3.3
> > log-adjacency-changes
> > area 0 authentication
> > redistribute connected subnets route-map CONNECTED
> > network 150.1.3.3 0.0.0.0 area 0
> > network 150.1.111.3 0.0.0.0 area 0
> > neighbor 150.1.111.5
> > neighbor 150.1.111.4
> > !
> > router bgp 34
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.3.0
> > neighbor 150.1.111.4 remote-as 34
> > !
> > ip classless
> > ip http server
> > !
> > route-map CONNECTED permit 10
> > match interface Ethernet0
> > !
> > !
> > !
> > !
> > ipx router eigrp 11
> > network 111
> > !
> > !
> > ipx router rip
> > no network 111
> > !
> > !
> > !
> > bridge 1 protocol ieee
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R3#
> > TermServ-34>4
> > [Resuming connection 4 to rack3r4 ... ]
> >
> > R4#sh run
> > Building configuration...
> >
> >
> >
> > Current configuration : 3401 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R4
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0004.0004.0004
> > !
> > !
> > dlsw local-peer peer-id 150.1.4.4
> > dlsw remote-peer 0 frame-relay interface Serial0 403
> > dlsw bridge-group 1
> > !
> > interface Loopback0
> > ip address 150.1.4.4 255.255.255.0
> > ipx network 4
> > !
> > interface Loopback10
> > ip address 195.1.4.4 255.255.255.0
> > !
> > interface Tunnel0
> > ip address 150.1.24.4 255.255.255.0
> > ipx network 24
> > ipx output-sap-filter 1001
> > tunnel source Loopback0
> > tunnel destination 150.1.2.2
> > !
> > interface Ethernet0
> > ip address 170.1.1.1 255.255.255.0
> > ipx input-sap-filter 1000
> > ipx network 1000
> > bridge-group 1
> > !
> > interface Serial0
> > ip address 150.1.111.4 255.255.255.248
> > encapsulation frame-relay
> > ip ospf authentication-key cisco
> > ip ospf priority 0
> > ipx network 111
> > ipx output-sap-filter 1001
> > no arp frame-relay
> > frame-relay map llc2 403 broadcast
> > frame-relay map ip 150.1.111.3 403 broadcast
> > frame-relay map ip 150.1.111.5 403 broadcast
> > frame-relay map ipx 111.0003.0003.0003 403 broadcast
> > frame-relay map ipx 111.0005.0005.0005 403 broadcast
> > no frame-relay inverse-arp
> > frame-relay lmi-type cisco
> > !
> > interface Serial1
> > ip address 150.1.14.4 255.255.255.0
> > ipx network 14
> > ipx output-sap-filter 1001
> > !
> > interface BRI0
> > no ip address
> > shutdown
> > isdn x25 static-tei 0
> > !
> > router eigrp 100
> > redistribute rip metric 1 1 1 1 1
> > network 150.1.14.4 0.0.0.0
> > network 150.1.24.4 0.0.0.0
> > auto-summary
> > no eigrp log-neighbor-changes
> > !
> > router ospf 1
> > router-id 150.1.4.4
> > log-adjacency-changes
> > area 0 authentication
> > redistribute rip subnets route-map RIP2OSPF
> > network 150.1.4.4 0.0.0.0 area 0
> > network 150.1.111.4 0.0.0.0 area 0
> > distance 171 0.0.0.0 255.255.255.255 1
> > !
> > router rip
> > timers basic 10 60 60 80
> > network 170.1.0.0
> > !
> > router bgp 34
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.4.0
> > neighbor 150.1.2.2 remote-as 256
> > neighbor 150.1.2.2 ebgp-multihop 255
> > neighbor 150.1.2.2 update-source Loopback0
> > neighbor 150.1.2.2 route-map MED out
> > neighbor 150.1.14.1 remote-as 1
> > neighbor 150.1.14.1 route-map MED out
> > neighbor 150.1.111.3 remote-as 34
> > neighbor 150.1.111.3 route-map MED out
> > neighbor 170.1.1.254 remote-as 100
> > neighbor 170.1.1.254 route-map NO-EXPORT in
> > !
> > ip classless
> > ip http server
> > ip as-path access-list 1 permit _1000_
> > ip as-path access-list 2 permit ^100_
> > !
> > !
> > ip access-list standard EVEN_SECOND_OCTET
> > permit 0.0.0.0 255.254.255.255
> > ip access-list standard ODD_THIRD_OCTET
> > permit 0.0.1.0 255.255.254.255
> > access-list 1 permit 150.1.30.0
> > access-list 1000 deny FFFFFFFF 4
> > access-list 1000 permit FFFFFFFF
> > access-list 1001 deny 1.0000.0000.0000 FFFFFFFE.ffff.ffff.ffff 7
> > access-list 1001 permit FFFFFFFF
> > route-map NO-EXPORT permit 10
> > match as-path 1
> > set community no-export
> > !
> > route-map NO-EXPORT permit 20
> > !
> > route-map MED permit 10
> > match ip address ODD_THIRD_OCTET
> > match as-path 2
> > set metric 31337
> > !
> > route-map MED permit 20
> > !
> > route-map RIP2OSPF permit 10
> > match ip address EVEN_SECOND_OCTET
> > set metric 1000
> > !
> > route-map RIP2OSPF permit 20
> > set metric-type type-1
> > !
> > !
> > !
> > !
> > ipx router eigrp 11
> > network 111
> > !
> > !
> > ipx router rip
> > no network 111
> > !
> > !
> > !
> > bridge 1 protocol ieee
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R4#
> > TermServ-34>5
> > [Resuming connection 5 to rack3r5 ... ]
> >
> > R5#sh run
> > Building configuration...
> >
> > Current configuration : 2019 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R5
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0005.0005.0005
> > ipx internal-network 5555
> > !
> > !
> > !
> > interface Loopback0
> > ip address 150.1.5.5 255.255.255.0
> > ipx network 5
> > !
> > interface Loopback10
> > ip address 195.1.5.5 255.255.255.0
> > !
> > interface Ethernet0
> > ip address 150.1.222.5 255.255.255.0
> > no ip redirects
> > ip ospf message-digest-key 1 md5 cisco
> > ip ospf network point-to-multipoint
> > ipx network 222
> > ipx nlsp enable
> > standby 1 ip 150.1.222.1
> > standby 1 preempt
> > standby 1 track Serial0 100
> > !
> > interface Serial0
> > ip address 150.1.111.5 255.255.255.248
> > encapsulation frame-relay
> > ip ospf authentication-key cisco
> > ip ospf priority 0
> > ipx network 111
> > no arp frame-relay
> > frame-relay map ip 150.1.111.3 503 broadcast
> > frame-relay map ip 150.1.111.4 503 broadcast
> > frame-relay map ipx 111.0003.0003.0003 503 broadcast
> > frame-relay map ipx 111.0004.0004.0004 503 broadcast
> > no frame-relay inverse-arp
> > frame-relay lmi-type cisco
> > !
> > interface Serial1
> > no ip address
> > shutdown
> > !
> > interface Serial2
> > no ip address
> > shutdown
> > !
> > interface Serial3
> > no ip address
> > shutdown
> > !
> > interface BRI0
> > no ip address
> > shutdown
> > isdn x25 static-tei 0
> > !
> > router ospf 1
> > router-id 150.1.5.5
> > log-adjacency-changes
> > area 0 authentication
> > area 51 authentication message-digest
> > area 51 virtual-link 150.1.2.2 authentication-key cisco
> > network 150.1.5.5 0.0.0.0 area 0
> > network 150.1.111.5 0.0.0.0 area 0
> > network 150.1.222.5 0.0.0.0 area 51
> > !
> > router bgp 256
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.5.0
> > neighbor 150.1.222.6 remote-as 256
> > !
> > ip classless
> > ip http server
> > !
> > !
> > !
> > !
> > ipx router eigrp 11
> > network 111
> > !
> > !
> > ipx router nlsp
> > area-address 0 0
> > !
> > !
> > ipx router rip
> > no network 111
> > no network 222
> > !
> > !
> > !
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R5#
> > TermServ-34>6
> > [Resuming connection 6 to rack3r6 ... ]
> >
> > R6#sh run
> > Building configuration...
> >
> > Current configuration : 1945 bytes
> > !
> > version 12.1
> > no service single-slot-reload-enable
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R6
> > !
> > logging rate-limit console 10 except errors
> > enable password cisco
> > !
> > ip subnet-zero
> > !
> > !
> > no ip finger
> > no ip domain-lookup
> > !
> > ipx routing 0006.0006.0006
> > ipx internal-network 6666
> > call rsvp-sync
> > cns event-service server
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > interface Loopback0
> > ip address 150.1.6.6 255.255.255.0
> > ipx network 6
> > !
> > interface Loopback10
> > ip address 195.1.6.6 255.255.255.0
> > !
> > interface BRI0/0
> > no ip address
> > shutdown
> > !
> > interface Ethernet0/0
> > ip address 150.1.222.6 255.255.255.0
> > ip ospf message-digest-key 1 md5 cisco
> > ip ospf network point-to-multipoint
> > half-duplex
> > ipx network 222
> > ipx nlsp enable
> > standby 1 priority 25 preempt
> > standby 1 ip 150.1.222.1
> > !
> > interface Serial0/0
> > no ip address
> > encapsulation frame-relay
> > shutdown
> > frame-relay lmi-type cisco
> > !
> > interface TokenRing0/0
> > no ip address
> > shutdown
> > ring-speed 16
> > !
> > interface FastEthernet1/0
> > no ip address
> > shutdown
> > duplex auto
> > speed auto
> > !
> > interface ATM3/0
> > no ip address
> > shutdown
> > no atm ilmi-keepalive
> > !
> > router ospf 1
> > router-id 150.1.6.6
> > log-adjacency-changes
> > area 51 authentication message-digest
> > network 150.1.6.6 0.0.0.0 area 51
> > network 150.1.222.6 0.0.0.0 area 51
> > !
> > router bgp 256
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.6.0
> > neighbor 150.1.222.2 remote-as 256
> > neighbor 150.1.222.2 route-reflector-client
> > neighbor 150.1.222.5 remote-as 256
> > neighbor 150.1.222.5 route-reflector-client
> > !
> > ip kerberos source-interface any
> > ip classless
> > no ip http server
> > !
> > !
> > !
> > !
> > ipx router nlsp
> > area-address 0 0
> > !
> > !
> > ipx router rip
> > no network 222
> > !
> > !
> > !
> > !
> > voice-port 2/0/0
> > !
> > voice-port 2/0/1
> > !
> > dial-peer cor custom
> > !
> > !
> > !
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > transport input none
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> >
> >
> >
> >
> >
> > > Guys,
> > >
> > > I have re created the configs for Cyscoexpert labs, since I was
>getting
> > > a
> > > few queries. It would create havoc to send the config to the whole
>group
> > > (also, zipped or attachments are not supported).
> > >
> > > Can someone suggest if a similar service exists on Group study FTP
> > > server
> > > (if such a thing exists). Otherwise I will prolly upload it on one
>of
> > > the
> > > free sites and post the url..
> > >
> > > The reason I want to do is to get the discussion on the ways other
> > > people
> > > have configged it, and I am also planning to suggest different ways
> > > (where
> > > possible) to acheive the same result.
> > >
> > > rgds
> > > Nick
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:36:37 GMT-3