From: Javed Tufail (jtufail@xxxxxxxxx)
Date: Thu Jul 18 2002 - 23:05:25 GMT-3
Where is your voice compression module on the router, I dont see that on sh
ver of your router. MC3810 has either VCM (voice comp mod)or HCM(high perf
comp mod). If you dont have any DSPs on the router the voice ports are not
initialized.
Javed
MC3810 SCB board (v01.B0)
1 Multiflex T1(slot 3) RJ45 interface(v03.A0)
1 Six-Slot Analog Voice Module (v03.K0)
1 Analog E&M voice interface (v05.B0) port 1/1
1 Analog E&M voice interface (v05.B0) port 1/2
1 Analog FXO voice interface (v03.K0) port 1/3
1 Analog FXO voice interface (v03.K0) port 1/4
1 Analog FXS voice interface (v03.A0) port 1/5
1 Analog FXS voice interface (v03.A0) port 1/6
1 6-DSP(slot2) High Performance Compression Module(v01.A0) <<=======
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
2 Serial(sync/async) network interface(s)
1 Channelized T1/PRI port(s)
256K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (AMD29F016)
Configuration register is 0x2102
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
kris.keen@aon.com.au
Sent: Thursday, July 18, 2002 5:36 PM
To: jtufail@cisco.com
Cc: ccielab@groupstudy.com; franjime@cisco.com;
louis.krucker@sunrise.net
Subject: RE: Anyone seen this?
Also,
r6#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r6(config)#voice-port 1/1
r6(config-voiceport)#no shut
r6(config-voiceport)#
00:04:18: %Voice system is not initialized.
00:04:18: %LINK-3-UPDOWN: Interface FXS 1/1, changed state to up
r6(config-voiceport)#
r6(config-voiceport)#
:(
-----------------------------------------------------------------
Kris Keen - CCNP, CCDP, CNE
Network Support Specialist - Network Systems
Aon Risk Services Australia Limited
(612) 9253 7272
0404862970
E: Kris.Keen@aon.com.au
Kris Keen
To: "Javed Tufail"
<jtufail@cisco.com>
19/07/2002 cc: ccielab@groupstudy.com,
franjime@cisco.com,
10:33 AM louis.krucker@sunrise.net
bcc:
Subject: RE: Anyone seen
this?(Document link: Kris Keen)
I've upgraded to 12.1(5)10T
I am still getting the error message on both units..\
Serial # 8704868
Version # 5.1
avm system bus fpga init pass:
:FPGA program OK.
avm fpga programming successful
:avm qslac fpga init pass:
:
00:00:31: 1/1 circuit type voice
00:00:31: 1/3 circuit type voice
00:00:31: %Voice system not initialized.RS366: VDM is not found
RS366: killing the process pid = 20.
00:00:47: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:47: %LINK-3-UPDOWN: Interface Serial1, changed state to down
00:00:47: %LINK-3-UPDOWN: Interface Serial0, changed state to down
00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to up
00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed
state to down
00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed
state to down
00:00:48: %LINK-3-UPDOWN: Interface FXS 1/1, changed state to
Administrative Shutdown
00:00:48: %LINK-3-UPDOWN: Interface E&M 1/3, changed state to
Administrative Shutdown
00:00:48: %SYS-5-CONFIG_I: Configured from memory by console
00:00:50: %LINK-5-CHANGED: Interface Serial0, changed state to
administratively down
00:00:50: %LINK-5-CHANGED: Interface Serial1, changed state to
administratively down
00:00:50: %LINK-5-CHANGED: Interface FR-ATM20, changed state to
administratively down
00:00:51: %LINEPROTO-5-UPDOWN: Line protocol on Interface FR-ATM20, changed
state to down
00:00:52: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) MC3810 Software (MC3810-A2JSV556I-M), Version 12.1(5)T10, RELEASE
SOFTWARE (fc2)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Tue 07-Aug-01 23:02 by ccaiInterface Ethernet0 assigned DHCP
address 192.168.1.23, mask 255.255.255.0
Translating "r6"...domain server (255.255.255.255) (192.168.1.1)
flashfs[9]: 1 files, 1 directories
flashfs[9]: 0 orphaned files, 0 orphaned directories
flashfs[9]: Total bytes: 16320000
flashfs[9]: Bytes used: 9513984
flashfs[9]: Bytes available: 6806016
flashfs[9]: flashfs fsck took 36 seconds.
flashfs[9]: Initialization complete.
r6>
-----------------------------------------------------------------
Kris Keen - CCNP, CCDP, CNE
Network Support Specialist - Network Systems
Aon Risk Services Australia Limited
(612) 9253 7272
0404862970
E: Kris.Keen@aon.com.au
"Javed Tufail"
<jtufail@cisco To: <kris.keen@aon.com.au>,
<louis.krucker@sunrise.net>,
.com> <franjime@cisco.com>
cc: <ccielab@groupstudy.com>
19/07/2002 bcc:
10:05 AM Subject: RE: Anyone seen this?
You are running an old code that showed this problem, I dont recall the
exact bug id but 12.0.9 for mc3810 has been deferred. Try changing the
code.
The next up from 12.0.9 was mc3810-a2binr3v2-mz.120-10.bin
Javed
-----Original Message-----
From: kris.keen@aon.com.au [mailto:kris.keen@aon.com.au]
Sent: Thursday, July 18, 2002 4:16 PM
To: louis.krucker@sunrise.net; jtufail@cisco.com; franjime@cisco.com
Cc: ccielab@groupstudy.com
Subject: RE: Anyone seen this?
00:00:02: %Voice system not initialized.
Type of VoicePort is E&MError: could not set value, code = -4
Type of VoicePort is FXSError: could not set value, code = -4
r5>
r5>sh ver
Cisco Internetwork Operating System Software
IOS (tm) MC3810 Software (MC3810-BINR3V2-M), Version 12.0(9), RELEASE
SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 25-Jan-00 01:27 by bettyl
Image text-base: 0x00023000, data-base: 0x006E9C58
ROM: System Bootstrap, Version 12.0(6r)T4, RELEASE SOFTWARE (fc1)
ROM: MC3810 Software (MC3810-WBOOT-M), Version 11.3(1)MA1, MAINTENANCE
INTERIM SOFTWARE
r5 uptime is 1 minute
System restarted by reload
System image file is "flash:mc3810-binr3v2-mz.120-9.bin"
Cisco MC3810 (MPC860) processor (revision 06.07) with 54784K/10752K bytes
of memory.
Processor board ID 09513084
PPC860 PowerQUICC, partnum 0x0000, version A03(0x0013)
Channelized E1, Version 1.0.
Bridging software.
MC3810 SCB board (v05.A0)
1 Multiflex T1(slot 3) RJ45 interface(v02.C0)
1 Six-Slot Analog Voice Module (v03.K0)
1 Analog E&M voice interface (v03.K0) port 1/1
1 Analog FXS voice interface (v03.K0) port 1/3
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
1 Channelized E1/PRI port(s)
1 Channelized T1/PRI port(s)
256K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (AMD29F016)
Configuration register is 0x2102
r5>
Any ideas guys?
I've got two units with the same issue :(
Cheers
-----------------------------------------------------------------
Kris Keen - CCNP, CCDP, CNE
Network Support Specialist - Network Systems
Aon Risk Services Australia Limited
(612) 9253 7272
0404862970
E: Kris.Keen@aon.com.au
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:36:36 GMT-3