From: Anthony Pace (anthonypace@xxxxxxxxxxx)
Date: Sun Jul 14 2002 - 16:43:35 GMT-3
So all cannonical non-cannonical issues are taken care of
transparently, exept if I want to advertise an Ethernet MAC via
ICANNREACH. Is that correct? In in this case we need to bit swap even
if the remote client could be on Ethernet himself.
Is this due to the fact that DLSw+ will bit bit swap the actual traffic
on one end (comming off the Ethernet), and unbit swap it on the other
end (going onto the ohter Ethernet)where two ethernet clients are
concerned. That means I need a third bit swap on the ICANREACH to make
it right? So if an Ethernet tries to go to 01 his router will turn it
into 80 and I would have had to advertise my 01 resource as 80 to
accomodate this?
Anthony PaAce
On Sat, 13 Jul 2002 23:12:16 -0700, "IPSec" <ipsec@myrealbox.com> said:
> it's in non-cannonical format already.
>
> -----Original Message-----
> From: "Nick Shah" <nshah@connect.com.au>
> To: "IPSec" <ipsec@myrealbox.com>, <ccielab@groupstudy.com>
> Date: Sun, 14 Jul 2002 16:06:10 +1000
> Subject: Re: Cyscoexpert Official Configs
>
> Wont the MAC address have to be bit swapped ??
>
> Nick
> ----- Original Message -----
> From: IPSec <ipsec@myrealbox.com>
> To: <ccielab@groupstudy.com>
> Sent: Sunday, July 14, 2002 3:12 PM
> Subject: Cyscoexpert Official Configs
>
>
> > Hi Group,
> >
> > Here are the official lab solutions:
> >
> > TermServ-34>1
> > [Resuming connection 1 to rack3r1 ... ]
> >
> > R1#sh run
> > Building configuration...
> >
> >
> >
> > Current configuration : 2014 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R1
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0001.0001.0001
> > !
> > !
> > dlsw local-peer peer-id 150.1.1.1
> > dlsw remote-peer 0 tcp 150.1.3.3
> > dlsw icanreach mac-exclusive
> > dlsw icanreach mac-address 7145.a0e3.0000 mask ffff.ffff.0000
> > dlsw bridge-group 1
> > !
> > interface Loopback0
> > ip address 150.1.1.1 255.255.255.0
> > ipx network 1
> > !
> > interface Loopback1
> > ip address 220.1.0.1 255.255.255.0
> > !
> > interface Loopback2
> > ip address 220.1.1.1 255.255.255.0
> > !
> > interface Loopback3
> > ip address 220.1.2.1 255.255.255.0
> > !
> > interface Loopback4
> > ip address 220.1.3.1 255.255.255.0
> > !
> > interface Loopback10
> > ip address 195.1.1.1 255.255.255.0
> > !
> > interface Ethernet0
> > ip address 150.1.10.1 255.255.255.0
> > ipx network 10
> > bridge-group 1
> > !
> > interface Serial0
> > ip address 150.1.14.1 255.255.255.0
> > ip summary-address eigrp 100 220.1.0.0 255.255.252.0 5
> > ipx network 14
> > no fair-queue
> > clockrate 2000000
> > !
> > interface Serial1
> > ip address 150.1.12.1 255.255.255.0
> > ipx network 12
> > clockrate 2000000
> > !
> > interface TokenRing0
> > no ip address
> > shutdown
> > !
> > router eigrp 100
> > network 150.1.14.1 0.0.0.0
> > network 220.1.0.0 0.0.3.255
> > auto-summary
> > no eigrp log-neighbor-changes
> > !
> > router ospf 1
> > router-id 150.1.1.1
> > log-adjacency-changes
> > area 12 nssa
> > network 150.1.1.1 0.0.0.0 area 12
> > network 150.1.12.1 0.0.0.0 area 12
> > !
> > router bgp 1
> > bgp log-neighbor-changes
> > network 195.1.1.0
> > neighbor 150.1.12.2 remote-as 256
> > neighbor 150.1.14.4 remote-as 34
> > neighbor 150.1.14.4 route-map PREPEND out
> > !
> > ip classless
> > ip http server
> > !
> > !
> > ip prefix-list R1_LOOPBACK seq 5 permit 195.1.1.0/24
> > route-map PREPEND permit 10
> > match ip address prefix-list R1_LOOPBACK
> > set as-path prepend 1 1
> > !
> > route-map PREPEND permit 20
> > !
> > !
> > !
> > !
> > !
> > bridge 1 protocol ieee
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R1#
> > TermServ-34>2
> > [Resuming connection 2 to rack3r2 ... ]
> >
> > R2#sh run
> > Building configuration...
> >
> > Current configuration : 2171 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R2
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0002.0002.0002
> > ipx internal-network 2222
> > !
> > !
> > !
> > interface Loopback0
> > ip address 150.1.2.2 255.255.255.0
> > ipx network 2
> > !
> > interface Loopback10
> > ip address 195.1.2.2 255.255.255.0
> > !
> > interface Tunnel0
> > ip address 150.1.24.2 255.255.255.0
> > ipx network 24
> > tunnel source Loopback0
> > tunnel destination 150.1.4.4
> > !
> > interface Ethernet0
> > ip address 150.1.222.2 255.255.255.0
> > no ip redirects
> > ip ospf message-digest-key 1 md5 cisco
> > ip ospf network point-to-multipoint
> > ipx network 222
> > ipx nlsp enable
> > standby 1 ip 150.1.222.1
> > standby 1 priority 50
> > standby 1 preempt
> > standby 1 track Serial0 50
> > !
> > interface Serial0
> > ip address 150.1.12.2 255.255.255.0
> > ipx network 12
> > no fair-queue
> > !
> > interface Serial1
> > no ip address
> > shutdown
> > !
> > router eigrp 100
> > redistribute ospf 1 metric 1 1 1 1 1
> > network 150.1.24.2 0.0.0.0
> > auto-summary
> > no eigrp log-neighbor-changes
> > !
> > router ospf 1
> > router-id 150.1.2.2
> > log-adjacency-changes
> > area 0 authentication
> > area 12 nssa
> > area 51 authentication message-digest
> > area 51 virtual-link 150.1.5.5 authentication-key cisco
> > redistribute eigrp 100 subnets
> > network 150.1.2.2 0.0.0.0 area 51
> > network 150.1.12.2 0.0.0.0 area 12
> > network 150.1.222.2 0.0.0.0 area 51
> > !
> > router bgp 256
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.2.0
> > neighbor 150.1.4.4 remote-as 34
> > neighbor 150.1.4.4 ebgp-multihop 255
> > neighbor 150.1.4.4 update-source Loopback0
> > neighbor 150.1.12.1 remote-as 1
> > neighbor 150.1.12.1 route-map LOCALPREF in
> > neighbor 150.1.222.6 remote-as 256
> > !
> > ip classless
> > ip http server
> > !
> > !
> > ip prefix-list R3_LOOPBACK seq 5 permit 195.1.3.0/24
> > route-map LOCALPREF permit 10
> > match ip address prefix-list R3_LOOPBACK
> > set local-preference 200
> > !
> > route-map LOCALPREF permit 20
> > !
> > !
> > !
> > !
> > ipx router nlsp
> > area-address 0 0
> > !
> > !
> > ipx router rip
> > no network 222
> > !
> > !
> > !
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R2#
> > TermServ-34>3
> > [Resuming connection 3 to rack3r3 ... ]
> >
> > R3#sh run
> > Building configuration...
> >
> >
> >
> > Current configuration : 1973 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R3
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0003.0003.0003
> > !
> > !
> > dlsw local-peer peer-id 150.1.3.3
> > dlsw remote-peer 0 tcp 150.1.1.1
> > dlsw remote-peer 0 frame-relay interface Serial0 304
> > dlsw icannotreach sap F0
> > dlsw bridge-group 1
> > !
> > interface Loopback0
> > ip address 150.1.3.3 255.255.255.0
> > ipx network 3
> > !
> > interface Loopback10
> > ip address 195.1.3.3 255.255.255.0
> > !
> > interface Serial0
> > ip address 150.1.111.3 255.255.255.248
> > encapsulation frame-relay
> > ip ospf authentication-key cisco
> > ip ospf priority 255
> > ipx network 111
> > no ipx split-horizon eigrp 11
> > no arp frame-relay
> > frame-relay map llc2 304 broadcast
> > frame-relay map ip 150.1.111.4 304 broadcast
> > frame-relay map ip 150.1.111.5 305 broadcast
> > frame-relay map ipx 111.0004.0004.0004 304 broadcast
> > frame-relay map ipx 111.0005.0005.0005 305 broadcast
> > no frame-relay inverse-arp
> > frame-relay lmi-type cisco
> > !
> > interface Serial1
> > no ip address
> > shutdown
> > !
> > interface Ethernet0
> > ip address 150.1.30.3 255.255.255.0
> > ipx network 30
> > bridge-group 1
> > !
> > interface BRI0
> > no ip address
> > shutdown
> > isdn x25 static-tei 0
> > !
> > router ospf 1
> > router-id 150.1.3.3
> > log-adjacency-changes
> > area 0 authentication
> > redistribute connected subnets route-map CONNECTED
> > network 150.1.3.3 0.0.0.0 area 0
> > network 150.1.111.3 0.0.0.0 area 0
> > neighbor 150.1.111.5
> > neighbor 150.1.111.4
> > !
> > router bgp 34
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.3.0
> > neighbor 150.1.111.4 remote-as 34
> > !
> > ip classless
> > ip http server
> > !
> > route-map CONNECTED permit 10
> > match interface Ethernet0
> > !
> > !
> > !
> > !
> > ipx router eigrp 11
> > network 111
> > !
> > !
> > ipx router rip
> > no network 111
> > !
> > !
> > !
> > bridge 1 protocol ieee
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R3#
> > TermServ-34>4
> > [Resuming connection 4 to rack3r4 ... ]
> >
> > R4#sh run
> > Building configuration...
> >
> >
> >
> > Current configuration : 3401 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R4
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0004.0004.0004
> > !
> > !
> > dlsw local-peer peer-id 150.1.4.4
> > dlsw remote-peer 0 frame-relay interface Serial0 403
> > dlsw bridge-group 1
> > !
> > interface Loopback0
> > ip address 150.1.4.4 255.255.255.0
> > ipx network 4
> > !
> > interface Loopback10
> > ip address 195.1.4.4 255.255.255.0
> > !
> > interface Tunnel0
> > ip address 150.1.24.4 255.255.255.0
> > ipx network 24
> > ipx output-sap-filter 1001
> > tunnel source Loopback0
> > tunnel destination 150.1.2.2
> > !
> > interface Ethernet0
> > ip address 170.1.1.1 255.255.255.0
> > ipx input-sap-filter 1000
> > ipx network 1000
> > bridge-group 1
> > !
> > interface Serial0
> > ip address 150.1.111.4 255.255.255.248
> > encapsulation frame-relay
> > ip ospf authentication-key cisco
> > ip ospf priority 0
> > ipx network 111
> > ipx output-sap-filter 1001
> > no arp frame-relay
> > frame-relay map llc2 403 broadcast
> > frame-relay map ip 150.1.111.3 403 broadcast
> > frame-relay map ip 150.1.111.5 403 broadcast
> > frame-relay map ipx 111.0003.0003.0003 403 broadcast
> > frame-relay map ipx 111.0005.0005.0005 403 broadcast
> > no frame-relay inverse-arp
> > frame-relay lmi-type cisco
> > !
> > interface Serial1
> > ip address 150.1.14.4 255.255.255.0
> > ipx network 14
> > ipx output-sap-filter 1001
> > !
> > interface BRI0
> > no ip address
> > shutdown
> > isdn x25 static-tei 0
> > !
> > router eigrp 100
> > redistribute rip metric 1 1 1 1 1
> > network 150.1.14.4 0.0.0.0
> > network 150.1.24.4 0.0.0.0
> > auto-summary
> > no eigrp log-neighbor-changes
> > !
> > router ospf 1
> > router-id 150.1.4.4
> > log-adjacency-changes
> > area 0 authentication
> > redistribute rip subnets route-map RIP2OSPF
> > network 150.1.4.4 0.0.0.0 area 0
> > network 150.1.111.4 0.0.0.0 area 0
> > distance 171 0.0.0.0 255.255.255.255 1
> > !
> > router rip
> > timers basic 10 60 60 80
> > network 170.1.0.0
> > !
> > router bgp 34
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.4.0
> > neighbor 150.1.2.2 remote-as 256
> > neighbor 150.1.2.2 ebgp-multihop 255
> > neighbor 150.1.2.2 update-source Loopback0
> > neighbor 150.1.2.2 route-map MED out
> > neighbor 150.1.14.1 remote-as 1
> > neighbor 150.1.14.1 route-map MED out
> > neighbor 150.1.111.3 remote-as 34
> > neighbor 150.1.111.3 route-map MED out
> > neighbor 170.1.1.254 remote-as 100
> > neighbor 170.1.1.254 route-map NO-EXPORT in
> > !
> > ip classless
> > ip http server
> > ip as-path access-list 1 permit _1000_
> > ip as-path access-list 2 permit ^100_
> > !
> > !
> > ip access-list standard EVEN_SECOND_OCTET
> > permit 0.0.0.0 255.254.255.255
> > ip access-list standard ODD_THIRD_OCTET
> > permit 0.0.1.0 255.255.254.255
> > access-list 1 permit 150.1.30.0
> > access-list 1000 deny FFFFFFFF 4
> > access-list 1000 permit FFFFFFFF
> > access-list 1001 deny 1.0000.0000.0000 FFFFFFFE.ffff.ffff.ffff 7
> > access-list 1001 permit FFFFFFFF
> > route-map NO-EXPORT permit 10
> > match as-path 1
> > set community no-export
> > !
> > route-map NO-EXPORT permit 20
> > !
> > route-map MED permit 10
> > match ip address ODD_THIRD_OCTET
> > match as-path 2
> > set metric 31337
> > !
> > route-map MED permit 20
> > !
> > route-map RIP2OSPF permit 10
> > match ip address EVEN_SECOND_OCTET
> > set metric 1000
> > !
> > route-map RIP2OSPF permit 20
> > set metric-type type-1
> > !
> > !
> > !
> > !
> > ipx router eigrp 11
> > network 111
> > !
> > !
> > ipx router rip
> > no network 111
> > !
> > !
> > !
> > bridge 1 protocol ieee
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R4#
> > TermServ-34>5
> > [Resuming connection 5 to rack3r5 ... ]
> >
> > R5#sh run
> > Building configuration...
> >
> > Current configuration : 2019 bytes
> > !
> > version 12.1
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R5
> > !
> > enable password cisco
> > !
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ipx routing 0005.0005.0005
> > ipx internal-network 5555
> > !
> > !
> > !
> > interface Loopback0
> > ip address 150.1.5.5 255.255.255.0
> > ipx network 5
> > !
> > interface Loopback10
> > ip address 195.1.5.5 255.255.255.0
> > !
> > interface Ethernet0
> > ip address 150.1.222.5 255.255.255.0
> > no ip redirects
> > ip ospf message-digest-key 1 md5 cisco
> > ip ospf network point-to-multipoint
> > ipx network 222
> > ipx nlsp enable
> > standby 1 ip 150.1.222.1
> > standby 1 preempt
> > standby 1 track Serial0 100
> > !
> > interface Serial0
> > ip address 150.1.111.5 255.255.255.248
> > encapsulation frame-relay
> > ip ospf authentication-key cisco
> > ip ospf priority 0
> > ipx network 111
> > no arp frame-relay
> > frame-relay map ip 150.1.111.3 503 broadcast
> > frame-relay map ip 150.1.111.4 503 broadcast
> > frame-relay map ipx 111.0003.0003.0003 503 broadcast
> > frame-relay map ipx 111.0004.0004.0004 503 broadcast
> > no frame-relay inverse-arp
> > frame-relay lmi-type cisco
> > !
> > interface Serial1
> > no ip address
> > shutdown
> > !
> > interface Serial2
> > no ip address
> > shutdown
> > !
> > interface Serial3
> > no ip address
> > shutdown
> > !
> > interface BRI0
> > no ip address
> > shutdown
> > isdn x25 static-tei 0
> > !
> > router ospf 1
> > router-id 150.1.5.5
> > log-adjacency-changes
> > area 0 authentication
> > area 51 authentication message-digest
> > area 51 virtual-link 150.1.2.2 authentication-key cisco
> > network 150.1.5.5 0.0.0.0 area 0
> > network 150.1.111.5 0.0.0.0 area 0
> > network 150.1.222.5 0.0.0.0 area 51
> > !
> > router bgp 256
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.5.0
> > neighbor 150.1.222.6 remote-as 256
> > !
> > ip classless
> > ip http server
> > !
> > !
> > !
> > !
> > ipx router eigrp 11
> > network 111
> > !
> > !
> > ipx router nlsp
> > area-address 0 0
> > !
> > !
> > ipx router rip
> > no network 111
> > no network 222
> > !
> > !
> > !
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> > R5#
> > TermServ-34>6
> > [Resuming connection 6 to rack3r6 ... ]
> >
> > R6#sh run
> > Building configuration...
> >
> > Current configuration : 1945 bytes
> > !
> > version 12.1
> > no service single-slot-reload-enable
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname R6
> > !
> > logging rate-limit console 10 except errors
> > enable password cisco
> > !
> > ip subnet-zero
> > !
> > !
> > no ip finger
> > no ip domain-lookup
> > !
> > ipx routing 0006.0006.0006
> > ipx internal-network 6666
> > call rsvp-sync
> > cns event-service server
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > interface Loopback0
> > ip address 150.1.6.6 255.255.255.0
> > ipx network 6
> > !
> > interface Loopback10
> > ip address 195.1.6.6 255.255.255.0
> > !
> > interface BRI0/0
> > no ip address
> > shutdown
> > !
> > interface Ethernet0/0
> > ip address 150.1.222.6 255.255.255.0
> > ip ospf message-digest-key 1 md5 cisco
> > ip ospf network point-to-multipoint
> > half-duplex
> > ipx network 222
> > ipx nlsp enable
> > standby 1 priority 25 preempt
> > standby 1 ip 150.1.222.1
> > !
> > interface Serial0/0
> > no ip address
> > encapsulation frame-relay
> > shutdown
> > frame-relay lmi-type cisco
> > !
> > interface TokenRing0/0
> > no ip address
> > shutdown
> > ring-speed 16
> > !
> > interface FastEthernet1/0
> > no ip address
> > shutdown
> > duplex auto
> > speed auto
> > !
> > interface ATM3/0
> > no ip address
> > shutdown
> > no atm ilmi-keepalive
> > !
> > router ospf 1
> > router-id 150.1.6.6
> > log-adjacency-changes
> > area 51 authentication message-digest
> > network 150.1.6.6 0.0.0.0 area 51
> > network 150.1.222.6 0.0.0.0 area 51
> > !
> > router bgp 256
> > no synchronization
> > bgp log-neighbor-changes
> > network 195.1.6.0
> > neighbor 150.1.222.2 remote-as 256
> > neighbor 150.1.222.2 route-reflector-client
> > neighbor 150.1.222.5 remote-as 256
> > neighbor 150.1.222.5 route-reflector-client
> > !
> > ip kerberos source-interface any
> > ip classless
> > no ip http server
> > !
> > !
> > !
> > !
> > ipx router nlsp
> > area-address 0 0
> > !
> > !
> > ipx router rip
> > no network 222
> > !
> > !
> > !
> > !
> > voice-port 2/0/0
> > !
> > voice-port 2/0/1
> > !
> > dial-peer cor custom
> > !
> > !
> > !
> > !
> > line con 0
> > exec-timeout 0 0
> > logging synchronous
> > transport input none
> > line aux 0
> > exec-timeout 0 0
> > logging synchronous
> > line vty 0 4
> > exec-timeout 0 0
> > logging synchronous
> > no login
> > !
> > end
> >
> >
> >
> >
> >
> >
> > > Guys,
> > >
> > > I have re created the configs for Cyscoexpert labs, since I was getting
> > > a
> > > few queries. It would create havoc to send the config to the whole group
> > > (also, zipped or attachments are not supported).
> > >
> > > Can someone suggest if a similar service exists on Group study FTP
> > > server
> > > (if such a thing exists). Otherwise I will prolly upload it on one of
> > > the
> > > free sites and post the url..
> > >
> > > The reason I want to do is to get the discussion on the ways other
> > > people
> > > have configged it, and I am also planning to suggest different ways
> > > (where
> > > possible) to acheive the same result.
> > >
> > > rgds
> > > Nick
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:36:30 GMT-3