From: P729 (p729@xxxxxxx)
Date: Mon Jul 08 2002 - 21:33:37 GMT-3
Carlos,
I never ran into this particular problem. Do you think specifying the
'bandwidth' parameter will have the same effect as fixing the ospf cost? Or
is something else going on?
Regards,
Mas Kato
https://ecardfile.com/id/mkato
----- Original Message -----
From: "Carlos G Mendioroz" <tron@huapi.ba.ar>
To: <Danny.Wang@alderwoods.com>
Cc: <ccielab@groupstudy.com>
Sent: Monday, July 08, 2002 1:00 PM
Subject: Re: ISDN and OSPF
> Danny,
> Short answer: fix the ospf cost of your ddr interfaces (via ip ospf
> cost).
>
> If you take a closer look, you should see that hellows are supressed for
> the
> DDR interfaces. The link is being set because of an LSU triggered by a
> change in
> cost of the link.
>
> HTH
>
> Danny.Wang@alderwoods.com wrote:
> >
> > Very simple scenario. R1 connected to R2 with both ISDN and Ethernet.
> >
> > Requiment:
> >
> > 1. Configure OSPF for the network
> > 2. Do not allow OSPF hello to keep the ISDN link up indefinitely
> > 3. The ISDN line should only come up when the ethernet connections
failed
> >
> > But after i enable the 'ip ospf demand circuit' on the dialer interface
> > (one side only), the link still constantly up and down, just wonderring
if
> > i missed something or it's a Teltone simulator "bug" ;-j
> >
> > When i enable debuy ip packet and dialer packet, it shows the dialer
caused
> > by hello packet, source ip address from dialer 1 to 224.0.0.5 ).
> >
> > when i modified the dialer-list on the R1, it's stopped, and leaving R2
as
> > is
> >
> > dialer list 1 protocol list 100
> > access-list 100 deny ospf any any
> > access-list 100 permit ip any any
> >
> > Any advice?
> >
> > R1------ISDN-------R2
> > \ /
> > \ /
> > Ethernet
> >
> > r1# sh run
> >
> > Building configuration...
> >
> > Current configuration : 1551 bytes
> > !
> > version 12.1
> > no service single-slot-reload-enable
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname r1
> > !
> > !
> > username CCIE2 password 0 cisco
> > username r2 password 0 cisco
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > ip audit notify log
> > ip audit po max-events 100
> > isdn switch-type basic-ni
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > interface Loopback0
> > ip address 10.10.11.1 255.255.255.255
> > !
> > interface Loopback1
> > ip address 10.10.12.1 255.255.255.255
> > !
> > interface Loopback2
> > ip address 10.10.13.1 255.255.255.255
> > !
> > interface Ethernet0/0
> > no ip address
> > shutdown
> > !
> > interface Serial0/0
> > no ip address
> > shutdown
> > no fair-queue
> > !
> > interface BRI0/0
> > no ip address
> > encapsulation ppp
> > dialer pool-member 1
> > isdn switch-type basic-ni
> > isdn spid1 0835866101 8358661
> > isdn spid2 0835866301 8358663
> > ppp authentication chap
> > ppp multilink
> > !
> > interface Ethernet0/1
> > ip address 192.168.1.211 255.255.255.0
> > !
> > interface Dialer1
> > ip address 172.19.1.6 255.255.255.252
> > encapsulation ppp
> > ip ospf demand-circuit
> > dialer pool 1
> > dialer remote-name CCIE2
> > dialer string 8358662
> > dialer-group 1
> > ppp authentication chap
> > ppp chap hostname CCIE1
> > ppp multilink
> >
> > !
> > router ospf 64
> > log-adjacency-changes
> > network 10.10.11.1 0.0.0.0 area 0
> > network 10.10.12.1 0.0.0.0 area 1
> > network 10.10.13.1 0.0.0.0 area 2
> > network 172.19.1.4 0.0.0.3 area 0
> > network 192.168.1.0 0.0.0.255 area 0
> > !
> > ip classless
> > ip http server
> > ip ospf name-lookup
> > !
> > dialer-list 1 protocol ip permit
> > !
> > !
> > alias exec r show run
> > alias exec c conf t
> > !
> > line con 0
> > exec-timeout 0 0
> > line aux 0
> > line vty 0 4
> > login
> > !
> > end
> >
> > r2#sh run
> > Building configuration...
> >
> > Current configuration : 1627 bytes
> > !
> > version 12.1
> > no service single-slot-reload-enable
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname r2
> > !
> > logging buffered 10000 debugging
> > !
> > username CCIE1 password 0 cisco
> > username r1 password 0 cisco
> > !
> > !
> > !
> > !
> > ip subnet-zero
> > no ip domain-lookup
> > !
> > isdn switch-type basic-ni
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > interface Loopback0
> > ip address 10.10.11.2 255.255.255.255
> > !
> > interface Loopback1
> > ip address 10.10.12.2 255.255.255.255
> > !
> > interface Loopback2
> > ip address 10.10.13.2 255.255.255.255
> > !
> > interface Ethernet0/0
> > no ip address
> > shutdown
> > !
> > interface Serial0/0
> > no ip address
> > shutdown
> > no fair-queue
> > !
> > interface BRI0/0
> > no ip address
> > encapsulation ppp
> > dialer pool-member 1
> > isdn switch-type basic-ni
> > isdn spid1 0835866201 8358662
> > isdn spid2 0835866401 8358664
> > ppp authentication chap
> > ppp multilink
> > !
> > interface Ethernet0/1
> > backup delay 2 2
> > backup interface Dialer1
> > ip address 192.168.1.212 255.255.255.0
> > !
> > interface Dialer1
> > ip address 172.19.1.5 255.255.255.252
> > encapsulation ppp
> > dialer pool 1
> > dialer remote-name CCIE1
> > dialer string 8358661
> > dialer load-threshold 128 either
> > dialer-group 1
> > ppp authentication chap
> > ppp chap hostname CCIE2
> > ppp multilink
> > !
> > router ospf 64
> > log-adjacency-changes
> > network 10.10.11.2 0.0.0.0 area 0
> > network 10.10.12.2 0.0.0.0 area 12
> > network 10.10.13.2 0.0.0.0 area 13
> > network 172.19.1.4 0.0.0.3 area 0
> > network 192.168.1.0 0.0.0.255 area 0
> > !
> > ip classless
> > ip http server
> > !
> > dialer-list 1 protocol ip permit
> > !
> > !
> > alias exec r show run
> > alias exec c conf t
> >
> > line con 0
> > exec-timeout 0 0
> > line aux 0
> > line vty 0 4
> > login
> > !
> > end
> >
> > Debug output:
> >
> > 00:44:45: IP: s=192.168.1.211 (local), d=224.0.0.5 (Ethernet0/1), len
68,
> > sendin
> > g broad/multicast
> > 00:44:49: IP: s=192.168.1.212 (Ethernet0/1), d=224.0.0.5, len 68, rcvd 0
> > 00:44:54: IP: s=172.19.1.6 (local), d=224.0.0.5 (Dialer1), len 64,
sending
> > broad
> > /multicast
> > 00:44:54: Di1 DDR: ip (s=172.19.1.6, d=224.0.0.5), 64 bytes, outgoing
> > interestin
> > g (ip PERMIT)
> > 00:44:54: IP: s=172.19.1.6 (local), d=224.0.0.5 (BRI0/0), len 64,
> > encapsulation
> > failed
> > 00:44:55: IP: s=192.168.1.211 (local), d=224.0.0.5 (Ethernet0/1), len
68,
> > sendin
> > g broad/multicast
> > 00:44:55: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> > 00:44:55: %DIALER-6-BIND: Interface BR0/0:1 bound to profile Di1
> > 00:44:56: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to
8358662
> > 00:44:56: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from
8358662
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:36:22 GMT-3