From: William Wong Kun Sing (wong_kunsing@xxxxxxxxxxxxxxxxx)
Date: Tue Jun 11 2002 - 00:25:16 GMT-3
Hi Tu
It seem like you have a different ipx network # on your tunnel interface and
it will not work. You have to have a same ipx network # on the tunnel.
Just treat the tunnel as a virtual link. Its also a good pratice to assign
an ipx address to the router when you enable the ipx routing like for
example "ipx routing 2.0.1" - for R2. This is because it will make your
life easy when you do frame relay map.
Best regards,
William
-----Original Message-----
From: Tu Nguyen [mailto:tunguyen@juniper.net]
Sent: Tuesday, June 11, 2002 8:57 AM
To: ccielab@groupstudy.com
Subject: ipx over gre tunnel
Hi,
I would wonder if anyone have a unique trick of getting ipx eigrp to
work over GRE tunnel or over ppp. I am not having any luck getting it to
work at all, appreciate if a sample config is display.
Thanks in advanced.
Tu
Here is mine version, but it's not working.
R2
!
ipx routing 00b0.6491.ae01
!
interface Tunnel0
no ip address
ip mtu 1440
ipx network 22
tunnel source 20.0.0.2
tunnel destination 30.0.0.3
!
ipx router eigrp 90
network 22
!
ipx router rip
no network 22
!
R3
ipx routing 0004.c135.ece0
!
interface Tunnel0
no ip address
ip mtu 1440
ipx network 33
tunnel source 30.0.0.3
tunnel destination 20.0.0.2
!
ipx router eigrp 90
network 33
!
I have also configures the ipx eigrp for the serial interface, which is
a back-to-back T1(ppp) link between the two routers but still not
working.
R3
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JK9O3S-M), Version 12.2(7b), RELEASE
SOFTWARE (fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 05-Mar-02 07:44 by pwade
Image text-base: 0x80008088, data-base: 0x81540B40
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
R3 uptime is 49 minutes
System returned to ROM by reload
System image file is "flash:c2600-jk9o3s-mz.122-7b.bin"
cisco 2621 (MPC860) processor (revision 0x102) with 60416K/5120K bytes
of memory.
Processor board ID JAD045244JH (1699577316)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Basic Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
--More--
00:49:34: %SYS-5-CONFIG_I: Configured from console 2 Serial network
interface(s)
4 ISDN Basic Rate interface(s)
Integrated NT1's for 4 ISDN Basic Rate interfaces
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
R2
R2#sh
00:51:03: %SYS-5-CONFIG_I: Configured from console by console
R2#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-JK9O3S-M), Version 12.2(7b), RELEASE
SOFTWARE (fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 05-Mar-02 01:14 by pwade
Image text-base: 0x600089A8, data-base: 0x61684000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
R2 uptime is 51 minutes
System returned to ROM by reload
System image file is "flash:c3640-jk9o3s-mz.122-7b.bin"
cisco 3640 (R4700) processor (revision 0x00) with 123904K/7168K bytes of
memory.
Processor board ID 17652080
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Basic Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
26 Serial network interface(s)
4 ISDN Basic Rate interface(s)
2 Channelized T1/PRI port(s)
2 Voice FXS interface(s)
Integrated NT1's for 4 ISDN Basic Rate interfaces
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
This archive was generated by hypermail 2.1.4 : Tue Jul 02 2002 - 08:12:31 GMT-3