From: John Neiberger (neiby@xxxxxxxxxx)
Date: Sun Apr 21 2002 - 12:33:04 GMT-3
First, what IOS are you using? I believe dialer watch is
unstable until 12.1(8).
I see that you're watching 15.1.1.0/24, but I'd bet that route
is not in your routing table. I'm thinking that you really
have 15.0.0.0/8. For dialer watch to work, it must be an exact
match.
I don't see anything else that is wrong. You don't need a
dialer list and dialer group since those are ignored when using
dialer watch, but I'm pretty sure they won't hurt anything.
Good luck,
John
---- On Sun, 21 Apr 2002, Eric Lamy (eric.lamy@wanadoo.fr)
wrote:
> Group,
>
> I have a problem with dialer watch.
> The router R2 detects the 15.1.1.0 route disparition but it
never dials.
> I put some debug : ip routing, dialer events and isdn q931.
> If I ping 14.0.0.3. dialing occurs and ping is OK.
>
> Any ideas on this?
>
> Thanks
>
> Eric LAMY
> eric.lamy@wanadoo.fr
>
>
>
>
> R2#sho run
> Building configuration...
>
> Current configuration : 1820 bytes
> !
> version 12.1
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname R2
> !
> logging rate-limit console 10 except errors
> !
> username R3 password 0 cisco
> ip subnet-zero
> !
> !
> no ip finger
> no ip domain-lookup
> !
> isdn switch-type basic-net3
> call rsvp-sync
> cns event-service server
> !
> !
> !
> !
> !
> !
> !
> !
> interface Ethernet0/0
> ip address 10.0.0.2 255.0.0.0
> half-duplex
> !
> interface Serial0/0
> no ip address
> encapsulation frame-relay
> !
> interface Serial0/0.4 multipoint
> ip address 13.0.0.2 255.0.0.0
> frame-relay map ip 13.0.0.4 113 broadcast
> !
> interface TokenRing0/0
> no ip address
> ring-speed 16
> !
> interface BRI0/0
> ip address 14.0.0.2 255.0.0.0
> encapsulation ppp
> dialer idle-timeout 60
> dialer watch-disable 15
> dialer map ip 15.1.1.0 name R3 broadcast 1008
> dialer map ip 14.0.0.3 name R3 broadcast 1008
> dialer watch-group 1
> dialer-group 1
> isdn switch-type basic-net3
> ppp authentication chap
> ppp multilink
> !
> interface Serial0/1
> no ip address
> shutdown
> !
> router eigrp 5
> network 10.0.0.0
> network 13.0.0.0
> network 14.0.0.0
> auto-summary
> no eigrp log-neighbor-changes
> !
> ip kerberos source-interface any
> ip classless
> no ip http server
> !
> access-list 120 deny eigrp any any
> access-list 120 permit ip any any
> dialer watch-list 1 ip 15.1.1.0 255.255.255.0
> dialer-list 1 protocol ip list 120
> !
> !
> dial-peer cor custom
> !
> !
> !
> alias configure ae alias exec
> alias exec i sho ip
> alias exec ip sho ip protocols
> alias exec ib sho ip int brie
> alias exec ir sho ip route
> alias exec e sho ip eigrp
> alias exec o sho ip ospf
> alias exec f sho ip frame
> alias exec b sho ip bgp
> alias exec r sho ip rip
> alias exec g sho ip igrp
> alias exec s sho run
> alias exec c conf t
> !
> line con 0
> transport input none
> line aux 0
> line vty 0 4
> !
> no scheduler allocate
> end
>
> R2#ir
> Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF
inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF NSSA
external type 2
> E1 - OSPF external type 1, E2 - OSPF external type 2,
E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia -
IS-IS inter
> area
> * - candidate default, U - per-user static route, o -
ODR
> P - periodic downloaded static route
>
> Gateway of last resort is not set
>
> C 10.0.0.0/8 is directly connected, Ethernet0/0
> D 11.0.0.0/8 [90/2185984] via 13.0.0.4, 00:00:27,
Serial0/0.4
> C 13.0.0.0/8 is directly connected, Serial0/0.4
> C 14.0.0.0/8 is directly connected, BRI0/0
> 15.0.0.0/24 is subnetted, 1 subnets
> D 15.1.1.0 [90/2185984] via 13.0.0.4, 00:00:27,
Serial0/0.4
> R2#
> R2#sho debug
> Dial on demand:
> Dial on demand events debugging is on
> IP routing:
> IP routing debugging is on
> ISDN:
> ISDN Q931 packets debugging is on
> ISDN Q931 packets debug DSLs. (On/Off/No DSL:1/0/-)
> DSL 0 --> 31
> 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - -
> R2#
> R2#sho isdn act
> --------------------------------------------------------------
---------------
> ---
> ISDN ACTIVE CALLS
> --------------------------------------------------------------
---------------
> ---
> Call Calling Called Remote Seconds Seconds
Seconds Charges
> Type Number Number Name Used Left Idle
> Units/Currency
> --------------------------------------------------------------
---------------
> ---
> --------------------------------------------------------------
---------------
> ---
> R2#
> 4d02h: RT: delete route to 11.0.0.0 via 13.0.0.4, eigrp
metric [90/2185984]
> 4d02h: RT: no routes to 11.0.0.0
> 4d02h: RT: delete route to 15.1.1.0 via 13.0.0.4, eigrp
metric [90/2185984]
> 4d02h: RT: no routes to 15.1.1.0
> 4d02h: DDR: Dialer Watch: watch-group = 1
> 4d02h: DDR: network 15.1.1.0/255.255.255.0 DOWN,
> 4d02h: DDR: primary DOWN
> 4d02h: DDR: Dialer Watch: Dial Reason: Primary of group 1 DOWN
> 4d02h: DDR: Dialer Watch: watch-group = 1,
> 4d02h: RT: garbage collecting entry for 11.0.0.0
> 4d02h: RT: garbage collecting entry for 15.1.1.0
> 4d02h: DDR: Dialer Watch: watch-group = 1
> 4d02h: DDR: network 15.1.1.0/255.255.255.0 DOWN,
> 4d02h: DDR: primary DOWN
> 4d02h: DDR: Dialer Watch: Dial Reason: Primary of group 1 DOWN
> 4d02h: DDR: Dialer Watch: watch-group = 1,
> 4d02h: RT: delete network route to 15.0.0.0
> R2#
> R2#sho isdn act
> --------------------------------------------------------------
---------------
> ---
> ISDN ACTIVE CALLS
> --------------------------------------------------------------
---------------
> ---
> Call Calling Called Remote Seconds Seconds
Seconds Charges
> Type Number Number Name Used Left Idle
> Units/Currency
> --------------------------------------------------------------
---------------
> ---
> --------------------------------------------------------------
---------------
> ---
>
> R2#ir
> Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF
inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF NSSA
external type 2
> E1 - OSPF external type 1, E2 - OSPF external type 2,
E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia -
IS-IS inter
> area
> * - candidate default, U - per-user static route, o -
ODR
> P - periodic downloaded static route
>
> Gateway of last resort is not set
>
> C 10.0.0.0/8 is directly connected, Ethernet0/0
> C 13.0.0.0/8 is directly connected, Serial0/0.4
> C 14.0.0.0/8 is directly connected, BRI0/0
>
> R2#
> R2#
>
> R2#sho version
> Cisco Internetwork Operating System Software
> IOS (tm) C2600 Software (C2600-JS-M), Version 12.1(5)T8,
RELEASE SOFTWARE
> (fc1)
> TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?
i=support
> Copyright (c) 1986-2001 by cisco Systems, Inc.
> Compiled Mon 07-May-01 22:07 by ccai
> Image text-base: 0x80008088, data-base: 0x813585F0
>
> ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE
(fc1)
> ROM: C2600 Software (C2600-JS-M), Version 12.1(5)T8, RELEASE
SOFTWARE (fc1)
>
> R2 uptime is 4 days, 2 hours, 48 minutes
> System returned to ROM by power-on
> System image file is "flash:c2600-js-mz.121-5.T8.bin"
>
> cisco 2612 (MPC860) processor (revision 0x101) with
61440K/4096K bytes of
> memory
> .
> Processor board ID JAD05220RL6 (2300065327)
> M860 processor: part number 0, mask 49
> Bridging software.
> X.25 software, Version 3.0.0.
> SuperLAT software (copyright 1990 by Meridian Technology
Corp).
> TN3270 Emulation software.
> Basic Rate ISDN software, Version 1.1.
> 1 Ethernet/IEEE 802.3 interface(s)
> 1 Token Ring/IEEE 802.5 interface(s)
> 2 Serial(sync/async) network interface(s)
> 1 ISDN Basic Rate interface(s)
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
> R2#
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:58:15 GMT-3