From: Babacar Diop (babacard2000@xxxxxxxxx)
Date: Fri Apr 19 2002 - 17:52:55 GMT-3
Now i have both routers configured with:
R5
dialer map llc2 name r3 broadcast 8358664
dialer map ip 133.14.35.6 name r3 broadcast 8358664
dialer-list 1 protocol ip permit
dialer-list 1 protocol llc2 permit
r3 is also configured with similar statements with the
dialer map pointing to R5.
The line is brought up my the OSPF LSA but when it's
brough down i can see can back up because of traffic
going from the token ring interface on R5 to the
ethernet of R3 as follows:
r5#sh dialer
BRI0 - dialer type = ISDN
Dial String Successes Failures Last DNIS
Last status
8358664 6 1 00:00:15
successful
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI0:1 - dialer type = ISDN
Idle timer (10 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is multilink member
Dial reason: ip (s=133.14.55.1, d=133.14.23.3)
Connected to 8358664 (r3)
BRI0:2 - dialer type = ISDN
Idle timer (10 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is multilink member
Dial reason: Multilink bundle overloaded
Connected to 8358664 (r3)
Any more ideas on this?
Thanks
--- DAN DORTON <DHSTS68@dhs.state.il.us> wrote:
> dialer maps too
>
> If you are using tcp you need to map ip layer 3 to
> layer 2.
>
> >>> "Perminder Grewal" <percy_gunner@hotmail.com>
> 04/19/02 12:52PM >>>
> Your 'dialer-list 1 protocol llc2 permit' seems to
> be wrong, you should
> define ip as your interesting traffic. The LLC2 is
> wrong, the dlsw uses TCP
> as the encapsulated protocol running over IP. DlSW
> terminates the LLC2
> locally.
>
> Regards
>
> Percy
>
>
> >From: Babacar Diop <babacard2000@yahoo.com>
> >Reply-To: Babacar Diop <babacard2000@yahoo.com>
> >To: cciegroup <ccielab@groupstudy.com>
> >Subject: DLSw+ & DDR
> >Date: Fri, 19 Apr 2002 10:23:49 -0700 (PDT)
> >
> >Here is my config on two routers. When i pull the
> >serial interface cable of R5, the isdn circuit does
> >not come up. I am doing anything wrong?
> >
> >
> >For R5
> >
> >username r3 password 0 cisco
> >!
> >isdn switch-type basic-ni
> >!
> >!
> >!
> >!
> >source-bridge ring-group 100
> >dlsw local-peer peer-id 133.14.55.1 promiscuous
> >dlsw remote-peer 0 tcp 133.14.23.6
> >dlsw remote-peer 0 tcp 133.14.23.3 backup-peer
> >133.14.23.6
> >!
> >interface Loopback0
> > ip address 133.14.5.5 255.255.255.0
> > ip ospf network point-to-point
> >!
> >interface Serial0
> > backup delay 10 200
> > backup interface BRI0
> > no ip address
> > encapsulation frame-relay
> > frame-relay lmi-type ansi
> >!
> >interface Serial0.1 point-to-point
> > ip address 133.14.56.5 255.255.255.0
> > frame-relay interface-dlci 506
> >!
> >interface Serial0.2 multipoint
> > ip address 133.14.243.5 255.255.255.0
> > no ip split-horizon
> > ip ospf priority 100
> > frame-relay interface-dlci 503
> > frame-relay interface-dlci 504
> >!
> >interface TokenRing0
> > ip address 133.14.55.1 255.255.255.248
> > ring-speed 16
> > source-bridge 10 1 100
> >!
> >interface BRI0
> > ip address 133.14.35.5 255.255.255.252
> > encapsulation ppp
> > dialer idle-timeout 10
> > dialer map llc2 name r3 broadcast 8358664
> > dialer load-threshold 1 either
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 0835866101 8358661
> > isdn spid2 0835866301 8358663
> > ppp authentication chap
> > ppp multilink
> >!
> >router ospf 64
> > log-adjacency-changes
> > area 3 range 133.14.51.0 255.255.255.0
> > area 3 virtual-link 200.200.200.1
> > network 133.14.5.0 0.0.0.255 area 0
> > network 133.14.35.4 0.0.0.3 area 3
> > network 133.14.51.0 0.0.0.15 area 3
> > network 133.14.55.0 0.0.0.7 area 0
> > network 133.14.56.0 0.0.0.255 area 0
> > network 133.14.243.0 0.0.0.255 area 0
> > neighbor 133.14.243.4
> > neighbor 133.14.243.3
> >!
> >ip classless
> >ip http server
> >!
> >dialer-list 1 protocol llc2 permit
> >
> >For R3:
> >
> >hostname r3
> >!
> >!
> >username r5 password 0 cisco
> >!
> >!
> >!
> >!
> >ip subnet-zero
> >no ip domain-lookup
> >!
> >isdn switch-type basic-ni
> >!
> >!
> >!
> >!
> >dlsw local-peer peer-id 133.14.23.3 promiscuous
> >dlsw remote-peer 0 tcp 133.14.23.6
> >dlsw bridge-group 1
> >!
> >interface Loopback0
> > ip address 133.14.3.3 255.255.255.0
> > ip ospf network point-to-point
> >!
> >interface Ethernet0
> > ip address 133.14.23.3 255.255.255.0
> > bridge-group 1
> >!
> >interface Serial0
> > no ip address
> > encapsulation frame-relay
> > no fair-queue
> > frame-relay lmi-type ansi
> >!
> >interface Serial0.1 multipoint
> > ip address 133.14.243.3 255.255.255.0
> > ip ospf priority 0
> > frame-relay interface-dlci 305
> >!
> >!
> >interface BRI0
> > ip address 133.14.35.6 255.255.255.252
> > encapsulation ppp
> > dialer idle-timeout 10
> > dialer map llc2 name r5 broadcast
> > dialer load-threshold 1 either
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 0835866201 8358662
> > isdn spid2 0835866401 8358664
> > ppp authentication chap
> > ppp multilink
> >!
> >router ospf 64
> > log-adjacency-changes
> > network 133.14.35.4 0.0.0.3 area 3
> > network 133.14.243.0 0.0.0.255 area 0
> > distribute-list 1 out igrp 64
> >!
> >ip classless
> >ip http server
> >!
> >dialer-list 1 protocol llc2 permit
> >!
> >
> >Thanks for your help.
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:58:14 GMT-3