From: Mingzhou Nie (mnie@xxxxxxxxx)
Date: Sat Apr 13 2002 - 02:17:08 GMT-3
Looks like it only shows the first page. Try "term leng 0".
--- Seaw Yong Kwan <seawyk@hotmail.com> wrote:
> Hi,
>
> Wondering if anyone has encountered a similiar problem.
>
> I upgraded the IOS of a Cisco 2514 to 12.1(2) with the E0 interface
> configured. However, when I do a show run, some of the interfaces are
> not
> listed. I have captured the log below.
>
> Can anyone advise?
>
> Cheers
>
> Maverick
>
> ------------------------------------------------------------
>
>
> C2500#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-I-L), Version 12.1(2), RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-2000 by cisco Systems, Inc.
> Compiled Tue 09-May-00 19:57 by linda
> Image text-base: 0x0303E424, data-base: 0x00001000
>
> ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a),
> RELEASE
> SOFTWARE (fc1)
>
> C2500 uptime is 2 minutes
> System returned to ROM by reload
> System image file is "flash:c2500-i-l.121-2.bin"
>
> cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of
> memory.
> Processor board ID 03894217, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> 2 Ethernet/IEEE 802.3 interface(s)
> 2 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
>
> Configuration register is 0x2102
>
> C2500#show run
> Building configuration...
>
> Current configuration:
> !
> version 12.1
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname C2500
> !
> enable password cisco
> !
> !
> !
> !
> !
> ip subnet-zero
> no ip domain-lookup
> !
> !
> !
> !
> interface Ethernet0
>
> C2500#show int e0
> Ethernet0 is up, line protocol is up
> Hardware is Lance, address is 0060.09c4.251e (bia 0060.09c4.251e)
> Internet address is 16.158.232.76/20
> MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA, loopback not set
> Keepalive set (10 sec)
> ARP type: ARPA, ARP Timeout 04:00:00
> Last input 00:00:00, output 00:00:06, output hang never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/40, 0 drops; input queue 0/75, 0 drops
> 5 minute input rate 3000 bits/sec, 4 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 495 packets input, 49807 bytes, 0 no buffer
> Received 494 broadcasts, 0 runts, 0 giants, 0 throttles
> 1 input errors, 0 CRC, 0 frame, 0 overrun, 1 ignored
> 0 input packets with dribble condition detected
> 22 packets output, 2604 bytes, 0 underruns
> 0 output errors, 0 collisions, 5 interface resets
> 0 babbles, 0 late collision, 0 deferred
> 0 lost carrier, 0 no carrier
> 0 output buffer failures, 0 output buffers swapped out
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:58:07 GMT-3