From: Ahmed Mamoor Amimi (mamoor@xxxxxxxx)
Date: Wed Apr 10 2002 - 12:55:36 GMT-3
Here we go again.... i guess ur looking for this. . : - )
Scenrio # 1
r1(0)---(e)----0(bridge)1----(e)---(0)r2
R1 :
conf t
dspu pu TEST rmac 4444.4444.4444 rsap 4 lsap 4
int e0
mac-address 2222.2222.2222
dspu enable-pu lsap 4
dspu start TEST
exit
R2 :
conf t
dspu host TEST rmac 2222.2222.2222 rsap 4 lsap 4
int e0
mac-address 4444.4444.4444
dspu enable-host lsap 4
dspu start TEST
exit
Scenrio # 2
r1(0)----(e)---0(bridge)1-----(e)----(0)r2
|
|
|
(TR)
|
|
r3
R1 :
conf t
dspu pu TEST rmac eeee.eeee.eeee rsap 6 lsap 6
interface e0
mac-address 2222.2222.2222
dspu start TEST1
dspu enable-host lsap 6
R3 :
conf t
dspu pu TEST rmac 4444.4444.4444 rsap 6 lsap 6
inter to0
mac-address 7777.7777.7777
dspu start TEST1
dspu enable-host lsap 6
multiring all
bridge config :
conf t
source-bridge ring-group 100
source-bridge transparent 100 1000 1 1
bridge 1 protocol ieee
bridge 1 bitswap-layer3-addresses
int e0
bridge-group 1
exit
int e1
bridge-group 1
exit
inter to0
source-bridge 10 1 100
source-bridge spanning
multiring all
exit
exit
Scenrio # 3
r1---(e)---(0)ra(dlsw)------(dlsw)rb(0)---(e)---r2
R1
conf t
dspu pu PU rmac 2222.2222.2222 rsap 4 lsap 4
int e0
mac-address 6666.6666.6666
dspu enable-pu lsap 4
dspu start test
exit
R2
conf t
dspu host PU xid-snd 00000000 rmac 6666.6666.6666 rsap 4 lsap 4
int e0
mac-address 2222.2222.2222
dspu enable-host lsap 4
dspu start PU
exit
Ra
conf t
dlsw local-peer peer-id 192.168.1.1
dlsw remote-peer 0 tcp 192.168.1.2
dlsw bridge-group 1
bridge 1 protocol ieee
inter e0
bridg-group 1
Rb
conf t
dlsw local-peer peer-id 192.168.1.2
dlsw remote-peer 0 tcp 192.168.1.1
dlsw bridge-group 1
bridge 1 protocol ieee
int e0
bridge-group 1
ra#sh dlsw circuits
Index local addr(lsap) remote addr(dsap) state uptime
1258291201 6666.6666.6666(04) 4444.4444.4444(04) CONNECTED
00:20:49
Total number of circuits connected: 1
rb#sh dlsw ci
Index local addr(lsap) remote addr(dsap) state uptime
1929379841 4444.4444.4444(04) 6666.6666.6666(04) CONNECTED
00:21:25
Total number of circuits connected: 1
Please do let me know if this paper helps u or not.
-Mamoor
----- Original Message -----
From: Adam Atkinson <Adam.Atkinson@damovo.com>
To: <ccielab@groupstudy.com>
Sent: Thursday, April 11, 2002 3:44 PM
Subject: "dspu" commands in Solie Skynet solution
> I notice there are several "dspu" commands in the suggested solution
> to the Skynet lab.
>
> I freely admit that dlsw is not one of my strong points, but looking
> through the lab I just cannot see which question these commands
> correspond to.
>
> I've found a page on CCO about dspu, but this doesn't
> help me identify the Skynet questions answered by these
> commands in the config.
>
> Or are they there for some other reason, e.g. to make dlsw circuits
> come up so you can tell if stuff is "working" or not?
>
> Adam Atkinson
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:58:06 GMT-3