From: Manny Gonzalez (manny@xxxxxxx)
Date: Mon Mar 25 2002 - 23:25:23 GMT-3
Memory? IOS version? Maybe do a sh ver and post it. Try Enterprise...
otherwise move down to IP/IPX/DEC Plus, then try IP Plus, then IP
only... but definitely is aeither the IOS version or the memory you have
on the box.
Nothing strange about it :-)
Louis Young wrote:
>
> r1#confi t
> Enter configuration commands, one per line. End with CNTL/Z.
> r1(config)#router ?
> bgp Border Gateway Protocol (BGP)
> egp Exterior Gateway Protocol (EGP)
> eigrp Enhanced Interior Gateway Routing Protocol (EIGRP)
> igrp Interior Gateway Routing Protocol (IGRP)
> isis ISO IS-IS
> iso-igrp IGRP for OSI networks
> mobile Mobile routes
> odr On Demand stub Routes
> ospf Open Shortest Path First (OSPF)
> rip Routing Information Protocol (RIP)
> static Static routes
>
> r1(config)#router isis
> r1(config)#
>
> ----- Original Message -----
> From: "Ahmed Mamoor Amimi" <mamoor@ieee.org>
> To: "Louis Young" <tonyblair@etang.com>; <ccielab@groupstudy.com>
> Sent: Monday, March 25, 2002 10:12 PM
> Subject: Re: Weird Symptom: can not enter (config-router)# mode in ISIS and O
SPF ,why???
>
> > Louis,
> > Ur not getting into the router-mode in OSPF just because u dont hav
e
> > any interface with ip address which
> > is to be assign to OSPF process.
> > Secondly ur not getting into the ISIS process as ur running
> > (C2600-IS-M) IPonly version. U need Enterprise
> > version to run isis. You will see ISIS when u do "router ?" but will not
> > able to get in to it if u dont have Enterprise version (js).
> >
> > -Mamoor
> >
> >
> > ----- Original Message -----
> > From: Louis Young <tonyblair@etang.com>
> > To: <ccielab@groupstudy.com>
> > Sent: Monday, March 25, 2002 2:38 PM
> > Subject: Weird Symptom: can not enter (config-router)# mode in ISIS and OSP
F
> > ,why???
> >
> >
> > > Dear all,
> > > I got the following phenomena during lab routers, it is a
> > 2610,pls help me out!
> > >
> > > Router(config)#
> > > Router(config)#router ospf 10
> > > Router(config)#
> > > 00:18:17: %OSPF-4-NORTRID: OSPF process 10 cannot start. There must be at
> > least one "up" IP interface, for OSPF to use as router ID
> > > Router(config)#router isis
> > > Router(config)#net 01.2222.2222.2222.00
> > > ^
> > > % Invalid input detected at '^' marker.
> > >
> > > Router(config)#^Z
> > > Router#sh ver
> > > 00:18:54: %SYS-5-CONFIG_I: Configured from console by console
> > > Cisco Internetwork Operating System Software
> > > IOS (tm) C2600 Software (C2600-IS-M), Version 12.1(10), RELEASE SOFTWARE
> > (fc1)
> > > Copyright (c) 1986-2001 by cisco Systems, Inc.
> > > Compiled Mon 06-Aug-01 23:48 by kellythw
> > > Image text-base: 0x80008088, data-base: 0x80CD6E7C
> > >
> > > ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
> > >
> > > Router uptime is 18 minutes
> > > System returned to ROM by reload
> > > System image file is "flash:c2600-is-mz.121-10.bin"
> > >
> > > cisco 2610 (MPC860) processor (revision 0x203) with 26624K/6144K bytes of
> > memory.
> > > Processor board ID JAD05270J95 (1358695238)
> > > M860 processor: part number 0, mask 49
> > > Bridging software.
> > > X.25 software, Version 3.0.0.
> > > 1 Ethernet/IEEE 802.3 interface(s)
> > > 1 Serial network interface(s)
> > > 32K bytes of non-volatile configuration memory.
> > > 8192K bytes of processor board System flash (Read/Write)
> > >
> > > Configuration register is 0x2102
> > >
> > >
> > > Thanks in advance.
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:57:22 GMT-3