From: DAN DORTON (DHSTS68@xxxxxxxxxxxxxxx)
Date: Mon Mar 18 2002 - 11:07:20 GMT-3
If you are using IPX EIGRP use the command.
IPX bandwidth-percent eigrp (AS#) (Percentage) on the interface.
IE:
router eigrp 100
network 172.168.0.0
!
interface serial 0
ip address 172.168.1.1 255.255.255.252
bandwidth 64
IPX bandwidth-percent eigrp 100 40
Dan
>>> "Ahmed Mamoor Amimi" <mamoor@ieee.org> 03/16/02 10:18PM >>>
U r right ...
but this option is not used alone. we can use WRED or CAR so that anything
above 40% will be discarded
this is my 0.02 cents
-Mamoor
----- Original Message -----
From: Sandro Ciffali <sandyccie@yahoo.com>
To: Ahmed Mamoor Amimi <mamoor@ieee.org>
Sent: Sunday, March 17, 2002 9:04 AM
Subject: Re: bandwidth
> May be i asked you question in a wrong way.
>
> If you have to control the bandwidth on serial link to
> allow it to use only 40% of bandwidth, you will use
> this map as out, How do you control bandwidth in?
> Since you don't have control on the incoming packets,
> You control what goes out not in.
> Similarly for ethernet how can u apply in if you can
> not control what comes in?
>
> Sandro
> --- Ahmed Mamoor Amimi <mamoor@ieee.org> wrote:
> > If traffic is coming from ethernet then it is IN
> > If traffic is coming to ethernet then it is OUT
> > Both condition is applicable to ethernet interface,
> > if applying somewhere
> > else then use the normal phenomena
> >
> > Let me know if this help !
> >
> > -Mamoor
> >
> >
> > ----- Original Message -----
> > From: Sandro Ciffali <sandyccie@yahoo.com>
> > To: Ahmed Mamoor Amimi <mamoor@ieee.org>
> > Sent: Sunday, March 17, 2002 5:42 AM
> > Subject: Re: bandwidth
> >
> >
> > > Ahmed,
> > > Should the service policy be applied in or out. I
> > > think it should be out. Can u pls confirm
> > >
> > > Sandro
> > > --- Ahmed Mamoor Amimi <mamoor@ieee.org> wrote:
> > > > How about !!
> > > >
> > > > class-map test
> > > > match access-list xxx <----------- where xxx
> > is
> > > > calling ipx
> > > > policy-map 123
> > > > class test
> > > > bandwidth percent 40
> > > >
> > > > on interface
> > > > service-policy 123 in
> > > >
> > > > this will make ur requirment i guess..
> > > >
> > > > here are some links :
> > > >
> > > >
> > >
> >
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120
> > > > t/120t5/iprtp.htm
> > > >
> > > >
> > >
> >
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120
> > > > t/120t7/friprtp.htm
> > > >
> > > >
> > > > -Mamoor
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: Merete Asak <merete@privat.sysedata.no>
> > > > To: <ccielab@groupstudy.com>
> > > > Sent: Saturday, March 16, 2002 6:37 PM
> > > > Subject: bandwidth
> > > >
> > > >
> > > > > Hi there,
> > > > >
> > > > > I have been reading alot about queuing and QoS
> > > > lately, and I'm trying to
> > > > find
> > > > > out what is best practice for a certain task.
> > > > > If I have a network that runs different sets
> > of
> > > > protocols, and I want to
> > > > make
> > > > > sure that a protocol (for example ipx) doesn't
> > use
> > > > more then a certain
> > > > amount
> > > > > of bandwith on an Ethernet, what should i use?
> > > > (Say I don't use any sort
> > > > of
> > > > > queuing on the interface, I just want to make
> > sure
> > > > IPX doesn't use more
> > > > then 40
> > > > > percent)
> > > > >
> > > > > Any good ideas?
> > > > >
> > > > > One other thing, does anyone have a good url
> > about
> > > > RTP and QoS for RTP?
> > > > >
> > > > > Thanks.
> > > > >
> > > > > Merete
> > > > >
> > > >
> > >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:57:12 GMT-3