From: Tshon (tshon@xxxxxxxxxxx)
Date: Tue Mar 12 2002 - 17:57:40 GMT-3
I believe you are missing the Broadcast command. If you add that to one
of the dialer commands... try a dialer map command
instead of a seperate dialer string , dialer name.... this will allow
you to add the broadcast command to the end.
Gregg Malcolm wrote:
>Joe,
>
>Can you give us the loop ip addresses on the wonderfull AS5300 as well ?
>
>
>----- Original Message -----
>From: "Joe Freeman" <joe.freeman@centurytel.com>
>To: "Ccielab" <ccielab@groupstudy.com>
>Sent: Tuesday, March 12, 2002 10:18 AM
>Subject: Eigrp over DDR using Dial Profiles?
>
>
>>Greetings-
>>
>>I think I'm probably just being dense at the moment, but I cannot get
>>
>EIGRP
>
>>to work via a dial backup line between a 2600 and a 5350.
>>
>>I can get PPP up with no problems. I can pass traffic using the default
>>static route in the 2600 pointing to the Dialer1 interface. I just can't
>>seem to get EIGRP to work. I'm obviously missing something, but I'll be
>>danged if I can see it at the moment.
>>
>>This will ultimately be a backup interface for a frame-relay connection on
>>another interface.
>>
>>Also, I should mention that this is IOS 12.2(8)T, Telco Plus. I know it's
>>bleeding edge, but 12.2(8)T is the only IOS that supports BOTH the
>>VWIC-MFT-T1 and the WIC1-AM. Telco Plus is the required feature set, as
>>there is no Enterprise Plus in 12.2(8)T.
>>
>>Thanks-
>>Joe Freeman, CCNP-VA/CCDP
>>
>>Here's important part of the 2600's config:
>>
>>interface Loopback0
>> ip address 10.130.254.1 255.255.255.255
>>!
>>interface FastEthernet0/0
>> ip address 10.0.209.249 255.255.252.0
>> speed 10
>> full-duplex
>>!
>>interface Async1
>> no ip address
>> encapsulation ppp
>> no ip mroute-cache
>> dialer in-band
>> dialer pool-member 1
>> dialer-group 1
>> autodetect encapsulation ppp
>> async default routing
>> async mode interactive
>> no peer default ip address
>> no fair-queue
>> no ppp microcode
>>!
>>interface Dialer1
>> ip unnumbered Loopback0
>> encapsulation ppp
>> dialer pool 1
>> dialer idle-timeout 300
>> dialer string 8070655
>> dialer hold-queue 50
>> dialer-group 1
>> no peer default ip address
>> ppp authentication pap callin
>> ppp pap sent-username <deleted> password 7 <deleted>
>>!
>>router eigrp 1
>> network 10.0.0.0
>> no auto-summary
>> no eigrp log-neighbor-changes
>>!
>>no ip http server
>>ip classless
>>ip route 0.0.0.0 0.0.0.0 Dialer1 250
>>ip pim bidir-enable
>>!
>>!
>>!
>>dialer-list 1 protocol ip permit
>>
>>Here's the config from the AS5350:
>>!
>>interface Serial3/0:23
>> description Test PRI
>> no ip address
>> encapsulation ppp
>> ip mroute-cache
>> no logging event link-status
>> dialer rotary-group 1
>> no snmp trap link-status
>> isdn switch-type primary-ni
>> isdn incoming-voice modem
>> isdn T306 30000
>> isdn T310 10000
>> no cdp enable
>>!
>>interface Async1
>> no ip address
>>!
>>interface Group-Async1
>> ip unnumbered Loopback1
>> encapsulation ppp
>> no ip route-cache
>> ip tcp header-compression passive
>> no ip mroute-cache
>> no logging event link-status
>> autodetect encapsulation ppp
>> async default routing
>> async dynamic routing
>> async mode interactive
>> ipx ppp-client Loopback0
>> ipx update interval sap changes-only
>> no snmp trap link-status
>> peer default ip address pool analog
>> compress stac
>> ppp authentication pap
>> group-range 1/00 1/107
>> hold-queue 75 in
>>!
>>interface Dialer1
>> ip unnumbered Loopback0
>> encapsulation ppp
>> no ip route-cache
>> no ip mroute-cache
>> no logging event link-status
>> dialer in-band
>> dialer idle-timeout 0
>> dialer load-threshold 1 outbound
>> dialer-group 1
>> ipx network ACCE99C
>> no snmp trap link-status
>> peer default ip address pool dialup-isdn
>> compress stac
>> no cdp enable
>> ppp authentication chap pap
>> ppp multilink
>>!
>>router eigrp 1
>> network 10.0.0.0
>> default-metric 10000 100 255 1 1500
>> no auto-summary
>> eigrp log-neighbor-changes
>>!
>>ip local pool Analog 10.0.31.1 10.0.31.254
>>ip local pool analog 10.0.249.1 10.0.249.254
>>ip local pool dialup-isdn 10.0.250.1 10.0.250.254
>>ip classless
>>ip flow-export destination 10.0.21.5 9996
>>ip flow-aggregation cache as
>> cache entries 2046
>> cache timeout inactive 200
>> cache timeout active 45
>> export destination 10.0.21.5 9996
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:57:02 GMT-3