From: Zakir A (procket1@xxxxxxxxxxx)
Date: Sat Mar 09 2002 - 20:15:18 GMT-3
Could somebody explain why he used IGMP instead of CGMP on the Catalyst5000?
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of Magdy
Louis
Sent: Sunday, February 17, 2002 6:23 AM
To: fwells12; ccielab@groupstudy.com
Subject: Re: Re: enchilada
No, that didnt solve it besides I disabled all protocols and interfaces but
ospf and same problem
As soon as you enable virtual link between R7 and R1 the following happens:
155.100.0.0/16 is variably subnetted, 11 subnets, 2 masks
C 155.100.127.0/24 is directly connected, Loopback0
O IA 155.100.123.0/24 [110/1563] via 155.100.35.1, 00:02:48, Serial0/0
O IA 155.100.122.0/24 [110/1563] via 155.100.35.1, 00:02:48, Serial0/0
O IA 155.100.121.1/32 [110/782] via 155.100.35.1, 00:02:48, Serial0/0
C 155.100.39.0/24 is directly connected, FastEthernet0/0.3
C 155.100.38.0/24 is directly connected, FastEthernet0/0.2
C 155.100.37.0/24 is directly connected, FastEthernet0/0.1
C 155.100.35.0/24 is directly connected, Serial0/0
O IA 155.100.34.0/24 [110/1562] via 155.100.35.1, 00:02:48, Serial0/0
O IA 155.100.33.0/24 [110/1563] via 155.100.35.1, 00:02:48, Serial0/0
O IA 155.100.32.0/24 [110/1572] via 155.100.35.1, 00:02:48, Serial0/0
R7#
R7#
R7#
R7#
R7#c
Enter configuration commands, one per line. End with CNTL/Z.
R7(config)#router ospf 1
R7(config-router)# area 10 virtual-link 155.100.121.1 auth cisco
R7(config-router)#^Z
R7#sh ip o v
Virtual Link OSPF_VL4 to router 155.100.121.1 is up
Run as demand circuit
DoNotAge LSA allowed.
Transit area 10, via interface Serial0/0, Cost of using 781
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:06
Adjacency State INIT (Hello suppressed)
Index 0/0, retransmission queue length 0, number of retransmission 0
First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
Last retransmission scan length is 0, maximum is 0
Last retransmission scan time is 0 msec, maximum is 0 msec
R7#
R7#sh ip rout
Gateway of last resort is not set
155.100.0.0/24 is subnetted, 5 subnets
C 155.100.127.0 is directly connected, Loopback0
C 155.100.39.0 is directly connected, FastEthernet0/0.3
C 155.100.38.0 is directly connected, FastEthernet0/0.2
C 155.100.37.0 is directly connected, FastEthernet0/0.1
C 155.100.35.0 is directly connected, Serial0/0
R7#
R7#
Notice how the virtual link has hello suppressed and init state ???
Any ideas ??
Magdy Louis
At 2/16/02 9:42:00 PM, you wrote:
>This is probably your problem...
>
>http://www.cisco.com/warp/public/104/10.html
>
>----- Original Message -----
>From: "Magdy Louis" <magdy@synergyct.com>
>To: <ccielab@groupstudy.com>
>Sent: Saturday, February 16, 2002 8:34 PM
>Subject: enchilada
>
>
>> Guys,
>>
>> For Solie's lab Enchilada:
>> Everything works fine but suddenly on R7 I see no O IA routes just O E2.
I
>traced it down to the following:
>> When I remove the virtual link between R1 and R7 everything is ok but
when
>I add it back routes disappear in few seconds although they are
>> still in the LSA database.
>>
>> Appreciate any feeback here ....
>>
>> ML
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:58 GMT-3